MudmotorTalk.com
http://www.mudmotortalk.com/mmt_v2/

Prodigy razor hull
http://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=73718		 Page 1 of 1
Author:  Zacha123 [ Wed Apr 10, 2019 1:55 pm ]
Post subject:  Prodigy razor hull
Looking to put a 37 prodrive on a prodigy razor hull. Thoughts? Should I go with elite or razor?
Author:  bluesky2012 [ Wed Apr 10, 2019 5:42 pm ]
Post subject:  Re: Prodigy razor hull
Dude you’ve been asking these same questions for 2 years. Just buy a hull to match your flat brim hat and go.


Sent from my iPhone using Tapatalk Pro
Author:  Wchauvin [ Wed Apr 10, 2019 9:10 pm ]
Post subject:  Re: Prodigy razor hull
Lol :D

I got a dude in breaux bridge that would build a boat wayyyyy better and cheaper than what you looking at..... just sayin lol
Author:  Zacha123 [ Thu Apr 11, 2019 3:11 am ]
Post subject:  Re: Prodigy razor hull
Haha y’all are worthless. Thanks for the help. Am I supposed to leave the tag on my flat bill?
Author:  Wchauvin [ Thu Apr 11, 2019 5:51 am ]
Post subject:  Re: Prodigy razor hull
Tag = certified :lol:
Author:  Russ [ Thu Apr 11, 2019 6:07 am ]
Post subject:  Re: Prodigy razor hull
Only if you dont have white framed sunglasses.

#CFFITR
#GhostBoat
#Whoneedsphysicsihaveamudmotor
Author:  JIMMY W [ Thu Apr 11, 2019 6:41 am ]
Post subject:  Re: Prodigy razor hull
Poodigy with a Poodrive = Turd
Author:  Wchauvin [ Thu Apr 11, 2019 8:02 am ]
Post subject:  Re: Prodigy razor hull
^ :lol:
Author:  Ducaholic [ Tue Apr 16, 2019 11:57 am ]
Post subject:  Re: Prodigy razor hull
Author:  Wchauvin [ Tue Apr 16, 2019 7:42 pm ]
Post subject:  Re: Prodigy razor hull
One is really sharp and the other not so much :D
Author:  Ricerunner [ Mon Apr 22, 2019 3:40 pm ]
Post subject:  Prodigy razor hull
I’ve got at an 1854 Prodigy with a stage 2 37 runs 32 on a fat blade from gator tail worked up to a 13p and handles a chop pretty good. Not unhappy with it. It’s Bigger than I anticipated from a 48” boat though


Sent from my iPhone using Tapatalk
Author:  Wchauvin [ Mon Apr 22, 2019 10:24 pm ]
Post subject:  Re: Prodigy razor hull
That’s good speeds. I’ve always heard that the prodigy boats perform well
Author:  Ricerunner [ Tue Apr 23, 2019 5:14 am ]
Post subject:  Re: Prodigy razor hull
there she be


Sent from my iPhone using Tapatalk
Author:  Wchauvin [ Tue Apr 23, 2019 5:37 am ]
Post subject:  Re: Prodigy razor hull
Very nice bro. What speeds you getting out of her?
Author:  Wchauvin [ Tue Apr 23, 2019 5:44 am ]
Post subject:  Re: Prodigy razor hull
My bad asking about the speeds again, I’m just getting off a 14 hour night shift and I’m trippin
Author:  Ricerunner [ Tue Apr 23, 2019 5:50 am ]
Post subject:  Prodigy razor hull
It’s running 32 on a 13p fat blade. It will run 34 on a merc 3 13.5p but I blow it out and barely get on step when taking off. I’ve got some more work to do like port and polish the intakes cam swap and back to a stainless works exhaust hoping to hold 34 @ 4900 rpms. I’ve got a buddy with an 1854 uncle J 3/16 running 34 on the fat blade and will hold 36 on the merc but like me he is blowing the prop out on the hole shot. He has a square chine where I have a triple taper and he is making more power than I am at the moment.
Author:  Wchauvin [ Tue Apr 23, 2019 1:55 pm ]
Post subject:  Re: Prodigy razor hull
Completely empty, I hold 33-34 with my 2 blade fat blade and I hold 36 empty with my 3 blade rapid. My hull is very light though so that’s probably why
Author:  Ricerunner [ Tue Apr 23, 2019 2:07 pm ]
Post subject:  Re: Prodigy razor hull
What hull and engine are you running


Sent from my iPhone using Tapatalk
Author:  Wchauvin [ Tue Apr 23, 2019 4:00 pm ]
Post subject:  Re: Prodigy razor hull
18x48 crawfish skiff in 1/8s custom built by Jeremy Brasseaux out of breaux bridge with a stage 1 40 GTR
Author:  Full Throttle [ Wed Apr 24, 2019 5:57 am ]
Post subject:  Re: Prodigy razor hull
Author:  Ricerunner [ Wed Apr 24, 2019 7:13 am ]
Post subject:  Re: Prodigy razor hull
Author:  Will [ Wed Apr 24, 2019 8:28 am ]
Post subject:  Re: Prodigy razor hull
Author:  Ricerunner [ Wed Apr 24, 2019 11:09 am ]
Post subject:  Re: Prodigy razor hull
Author:  Wchauvin [ Wed Apr 24, 2019 12:24 pm ]
Post subject:  Re: Prodigy razor hull
Everyone’s “level 1-3” opinions are different. We did basically a bolt on build on it, different air filter, different air cover, exhaust, cut skeg, and prop work. Going to get marcus or will to do some more in the future on it once I get this money right lol
Author:  Will [ Wed Apr 24, 2019 5:28 pm ]
Post subject:  Re: Prodigy razor hull
Author:  Wchauvin [ Wed Apr 24, 2019 7:25 pm ]
Post subject:  Re: Prodigy razor hull
Bro, I want to, but I’m a public servant with public servant pay and I have a beautiful 1 1/2 year old princess at home, so saving money is a must and it takes time. It’s the struggle, but hey, I appreciate and take care of my things cause of it lol
Author:  Will [ Thu Apr 25, 2019 4:21 am ]
Post subject:  Re: Prodigy razor hull
I get that, mine will be 8 soon, times flies and I've learned not to hold back. Buy, sell or trade to get what you want to play with. It doesn't cost that much if you do all the work yourself. I really don't see the need for a cam in the new 40, it's already pretty decent. I did a cam in mine but I wanted to. Get a good set of heads and a tuner and do the work yourself, it will open it up.
Author:  Wchauvin [ Thu Apr 25, 2019 5:53 am ]
Post subject:  Re: Prodigy razor hull
Yeah that exactly what I plan on doing, heads and a tune. Yeah I agree with you on that. A few months ago, I worked 46 hours of overtime in one pay period and sold 3 guns and bought me a benelli sbe 3 that I had been wanting. Now I need to work that overtime and sell some more things I don’t need to get the boat all finished up lol
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/