| MudmotorTalk.com http://www.mudmotortalk.com/mmt_v2/ |
|
| new style connecting rod part # http://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=3&t=35370 |
Page 1 of 1 |
| Author: | 50fps [ Sat Dec 15, 2012 9:11 am ] |
| Post subject: | new style connecting rod part # |
Anybody have the new style connecting rod part # handy? My aftermarket ones are out of spec and I am assuming the new factory ones are better than the old style. |
|
| Author: | deadbird8 [ Mon Dec 17, 2012 6:14 am ] |
| Post subject: | Re: new style connecting rod part # |
Typed in the old style number 841838 in a few parts sites and they don't show a replacement number so it may be a direct replacement w/o a part number change. May be trial and error, I have not personally seen the new style ones but Craig posted a while ago that they are black in color vs silver. It may be trial and error on the order. If replacing your c-rods make sure you do your wrist pins too. |
|
| Author: | Team Camo [ Mon Dec 17, 2012 6:44 am ] |
| Post subject: | Re: new style connecting rod part # |
I've still got the boxes from the set I installed a while back. I'll try to get time to look when I get home |
|
| Author: | 50fps [ Thu Dec 20, 2012 7:34 am ] |
| Post subject: | Re: new style connecting rod part # |
| Author: | 50fps [ Thu Dec 20, 2012 7:39 am ] |
| Post subject: | Re: new style connecting rod part # |
| Author: | Team Camo [ Thu Dec 20, 2012 8:51 pm ] |
| Post subject: | Re: new style connecting rod part # |
Sorry I took so long, but here ya go |
|
| Author: | deadbird8 [ Thu Dec 20, 2012 9:09 pm ] |
| Post subject: | Re: new style connecting rod part # |
Looks like its a direct replacement |
|
| Author: | Team Camo [ Thu Dec 20, 2012 9:17 pm ] |
| Post subject: | Re: new style connecting rod part # |
When I ordered I just asked for a pair of rods. The parkerized rods were what I got. Never even noticed the part # was the same till now. |
|
| Author: | 50fps [ Fri Dec 21, 2012 6:46 am ] |
| Post subject: | Re: new style connecting rod part # |
| Author: | Team Camo [ Fri Dec 21, 2012 7:04 am ] |
| Post subject: | Re: new style connecting rod part # |
Well I say parkerized, they were black & rough to the touch |
|
| Author: | 50fps [ Fri Dec 21, 2012 9:38 am ] |
| Post subject: | Re: new style connecting rod part # |
Got it. |
|
| Author: | jwoods823 [ Fri May 02, 2014 9:27 am ] |
| Post subject: | Re: new style connecting rod part # |
I know this is old but what is spec for these rods? |
|
| Author: | Puddler45 [ Fri May 02, 2014 10:01 am ] |
| Post subject: | Re: new style connecting rod part # |
made in china |
|
| Author: | cb5331 [ Fri May 02, 2014 10:04 am ] |
| Post subject: | Re: new style connecting rod part # |
^:lol: |
|
| Author: | Inkawhootz [ Fri May 02, 2014 11:23 am ] |
| Post subject: | Re: new style connecting rod part # |
Mitchv can you tell me the wrist pin diamater and crank journal diamater of that rod Sent from my SGH-M919 using Tapatalk |
|
| Author: | jwoods823 [ Fri May 02, 2014 1:14 pm ] |
| Post subject: | Re: new style connecting rod part # |
If only he could tell me where to find that girl in his avatar. |
|
| Author: | Puddler45 [ Fri May 02, 2014 1:59 pm ] |
| Post subject: | Re: new style connecting rod part # |
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|