|
|
FAQ
• Login
|
|
It is currently Tue May 13, 2025 5:34 pm
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Pattern for torquing head bolts?
| Author |
Message |
|
ibfishin
MMT 1000 Club
Joined: Sun Dec 05, 2010 8:20 pm
Posts: 1127
Location: Okeechobee, FL
|
 Pattern for torquing head bolts? Anybody tell me what the pattern should be?
Sent from my SM-G920V using Tapatalk
_________________
35 GTR pushing an 18' Alumitech Custom
|
| Wed Feb 10, 2016 6:38 pm |
|
|
|
SCmudder7071
MMT 1000 Club
Joined: Mon Feb 07, 2011 12:10 pm
Posts: 3024
|
Re: Pattern for torquing head bolts? Bottom left, top center, bottom right, top left, bottom center, top right
_________________
1754 Extreme/LAProp Stage 2 GTR
|
| Wed Feb 10, 2016 6:55 pm |
|
|
|
JD145
MMT 1000 Club
Joined: Wed Jun 04, 2014 9:01 pm
Posts: 1289
Location: SWGA
|
Re: Pattern for torquing head bolts?
_________________
1854 Prodigy DPE Level 3 HDR
|
| Wed Feb 10, 2016 7:00 pm |
|
|
|
ibfishin
MMT 1000 Club
Joined: Sun Dec 05, 2010 8:20 pm
Posts: 1127
Location: Okeechobee, FL
|
Re: Pattern for torquing head bolts? Thanks... another question. I noticed the head gasket has a slightly raised area around the perimeter of the cylinder and oil galleys. Should that surface face down against the block or up against the head?
Sent from my SM-G920V using Tapatalk
_________________
35 GTR pushing an 18' Alumitech Custom
|
| Wed Feb 10, 2016 7:13 pm |
|
|
|
deadbird8
MMT 1000 Club
Joined: Wed Feb 04, 2009 7:50 pm
Posts: 3833
Location: Old East Dallas, Texas
|
Re: Pattern for torquing head bolts?
_________________
Excel 1851F4 w/ MB35HD+R CDI with a little bit of this and little bit of that
|
| Thu Feb 11, 2016 6:04 am |
|
|
|
ibfishin
MMT 1000 Club
Joined: Sun Dec 05, 2010 8:20 pm
Posts: 1127
Location: Okeechobee, FL
|
Re: Pattern for torquing head bolts? Thanks... haven't tried to put them on yet, I just looked at the gasket and noticed both sides were not the same. Probably would have figured it out pretty quickly during the install.
Sent from my SM-G920V using Tapatalk
_________________
35 GTR pushing an 18' Alumitech Custom
|
| Thu Feb 11, 2016 6:23 am |
|
|
|
MaXXis85
MMT Elite Member
Joined: Wed Jan 14, 2009 7:23 am
Posts: 6233
Location: Tarkington, TX
|
Re: Pattern for torquing head bolts? Everyone will have there own way, I torque them in 2 stages. Working from the center bolts out.
_________________
Bayou Surface Drive
337-351-0362
Tarkington, TX 77327
|
| Thu Feb 11, 2016 6:37 am |
|
|
|
deadbird8
MMT 1000 Club
Joined: Wed Feb 04, 2009 7:50 pm
Posts: 3833
Location: Old East Dallas, Texas
|
Re: Pattern for torquing head bolts?
_________________
Excel 1851F4 w/ MB35HD+R CDI with a little bit of this and little bit of that
|
| Thu Feb 11, 2016 8:28 pm |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: Google [Bot] and 192 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
