Author |
Message |
JBsuperG
MMT Pro Member
Joined: Wed Mar 21, 2018 2:51 pm Posts: 263 Location: Michigan
|
What would you consider low or high hours on a surface drive
I am looking to buy a used boat with a surface drive. I was wondering what you guys would consider to be low hours and what would be high hours? I have been around boats my whole life but never boats with mud motors.
|
Wed Mar 28, 2018 4:25 pm |
|
|
flint87
MMT 1000 Club
Joined: Sun Dec 14, 2014 2:21 pm Posts: 3214
|
Re: What would you consider low or high hours on a surface d
|
Wed Mar 28, 2018 7:07 pm |
|
|
Russ
MMT 1000 Club
Joined: Mon Dec 31, 2012 11:07 pm Posts: 4820 Location: West Monroe, LA
|
Re: What would you consider low or high hours on a surface d
Bought one with something approching 850 hours, replaced the clutch, the bearings in the lower unit, muffler, a regulator, and a coil. Not too bad considering none of that had ever been changed except the bearings in the lower unit. It needs a new stator right now, but that only affects charging.
#CFFITR #TheGhostBoat #whoneedsphysicsihaveamudmotor
|
Wed Mar 28, 2018 8:45 pm |
|
|
Bigbend
MMT Pro Member
Joined: Sat Dec 11, 2010 6:25 am Posts: 493 Location: SWGA
|
Re: What would you consider low or high hours on a surface d
I've seen motors that look like they've spent a month on the bottom of the Atlantic with 100 hours, I've seen some with 500 hours that were well maintained and looked great, it really depends.
I'm a cheap SOB, so I always buy used. If you can tell that the seller is clearly a dumbass it's probably safe to assume that routine maintenance and TLC were not done. I bought a long tail that had 1,100 hours for $700. It needed new coils, new wiring harness, kill switch, prop, seals, throttle, choke rod and GD grease auto loader. The owner said it was in good condition. After I replaced all of that I put 200 hours on it without a hiccup. My current SD was bought with 130 hours, no issues at all 3 years later. Main thing to look at in my opinion is the case for leaks, check the oil level, make sure it cranks up without any issues and runs smooth. Check the compression if you want. There are good deals out there, and most of this stuff is pretty easy to replace/fix. There is thread on here about hours, some of the guys on here have motors with thousands of hours with nothing but oil, filter and seal changes.
|
Thu Mar 29, 2018 4:33 am |
|
|
MatterOM
MMT Member
Joined: Sat Oct 05, 2013 8:10 pm Posts: 22
|
Re: What would you consider low or high hours on a surface d
|
Sat Mar 31, 2018 12:59 pm |
|
|
flint87
MMT 1000 Club
Joined: Sun Dec 14, 2014 2:21 pm Posts: 3214
|
Re: What would you consider low or high hours on a surface d
|
Sat Mar 31, 2018 3:10 pm |
|
|
JBsuperG
MMT Pro Member
Joined: Wed Mar 21, 2018 2:51 pm Posts: 263 Location: Michigan
|
Re: What would you consider low or high hours on a surface d
I got a pretty good deal on one with less than 2 hours on it. Like new for Used price.
|
Sun Apr 01, 2018 6:04 am |
|
|
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
Re: What would you consider low or high hours on a surface d
_________________ Refurbishing a Prodrive
|
Sun Apr 01, 2018 6:07 am |
|
|
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
Re: What would you consider low or high hours on a surface d
_________________ Refurbishing a Prodrive
|
Sun Apr 01, 2018 6:09 am |
|
|
flint87
MMT 1000 Club
Joined: Sun Dec 14, 2014 2:21 pm Posts: 3214
|
Re: What would you consider low or high hours on a surface d
|
Sun Apr 01, 2018 6:16 am |
|
|
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
Re: What would you consider low or high hours on a surface d
_________________ Refurbishing a Prodrive
|
Sun Apr 01, 2018 6:20 am |
|
|
flint87
MMT 1000 Club
Joined: Sun Dec 14, 2014 2:21 pm Posts: 3214
|
Re: What would you consider low or high hours on a surface d
|
Sun Apr 01, 2018 7:18 am |
|
|
TGunn
MMT F.E.
Joined: Tue Feb 05, 2013 8:39 pm Posts: 764
|
Re: What would you consider low or high hours on a surface d
Sure, the price is absolutely ridiculous.
But it's not more ridiculous than 98% of the low-ball, brokedick assheads on here who think that coming within $2500 of asking price might just make a deal happen.
Selling anything on here is a real adventure.
My personal favorites are:
Via PM: 1) WHAT'S YOUR BOTTOM DOLLAR?!?!? (So they can then knock 25% off that.)
or,
(2) CASH IN HAND!!!!
Well no shit, buddy. Did you think I was going to offer 0% financing?
The hoops that I've jumped through to prove my used motors for sale are in excellent condition are unreal, and after I do that, potential buyers still act as though it's in fair condition regardless of videos, pictures, and warranties. It's almost not worth listing anything on this site.
|
Tue Apr 03, 2018 8:26 am |
|
|
50fps
MMT 1000 Club
Joined: Tue Jan 13, 2009 6:42 pm Posts: 2377 Location: West Coast Wisconsin
|
Re: What would you consider low or high hours on a surface d
|
Tue Apr 03, 2018 9:14 am |
|
|
Koondog62
MMT Pro Member
Joined: Thu Jul 20, 2017 6:23 am Posts: 129
|
Re: What would you consider low or high hours on a surface d
|
Tue Apr 03, 2018 10:58 am |
|
|
|