| MudmotorTalk.com http://www.mudmotortalk.com/mmt_v2/ |
|
| copperhead 12 bushing http://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=31485 |
Page 1 of 1 |
| Author: | grasshopper [ Mon Aug 13, 2012 6:16 pm ] |
| Post subject: | copperhead 12 bushing |
Ok my shaft has a rattling sound and there is a little play up and down .. not any noticeable side to side .. is that normal wear .. it looks fairly simple to repair .. is it ? Any tricks I need to know ? |
|
| Author: | garrettpearce [ Tue Aug 14, 2012 7:13 am ] |
| Post subject: | Re: copperhead 12 bushing |
Normal for a copperhead. It'll happen time and time again |
|
| Author: | cmiller73 [ Tue Aug 14, 2012 10:59 am ] |
| Post subject: | Re: copperhead 12 bushing |
Grease the crap out of it. And make sure you grease it before every outing. It will save on the wear of the bushing. |
|
| Author: | grasshopper [ Tue Aug 14, 2012 11:14 am ] |
| Post subject: | Re: copperhead 12 bushing |
Is there any trouble in replacing it .. a friend of mine jade a machine shop what about one made of teflon .. we use bushing at work made of this.. they last for ever even ware down stainless steel |
|
| Author: | scott0227 [ Wed Aug 15, 2012 5:57 pm ] |
| Post subject: | Re: copperhead 12 bushing |
Its not bad but, the hub is screwed to the shaft housing with reverse threads. It also has red loctite so it needs to be heated. The gear for the belt at the rear of the prop shaft comes of easy with a light impact with allen head adapter. Use the prop shaft to tap out the bushing. I like the idea u got for the bushing. let us know if it works. |
|
| Author: | scott0227 [ Wed Aug 15, 2012 6:01 pm ] |
| Post subject: | Re: copperhead 12 bushing |
Also I think you can over grease it and blow out the prop shaft seal. |
|
| Author: | grasshopper [ Wed Aug 15, 2012 7:33 pm ] |
| Post subject: | Re: copperhead 12 bushing |
Oh snap .. I have to take the shaft off ... Is the bushing that tight ? I think I can get it off without pulling lower unit apart ... Has anyone tried to pull bushing without dis assembling shaft ... Only thing I'm worried about on teflon bushing is high revaluation... We use em in a lot lower rpms ... |
|
| Author: | grasshopper [ Wed Aug 15, 2012 7:44 pm ] |
| Post subject: | Re: copperhead 12 bushing |
I bought this motor used ... Don't have any experience with them .. I'm a decent mech. Tho ... So help is very much need |
|
| Author: | scott0227 [ Thu Aug 16, 2012 4:40 pm ] |
| Post subject: | Re: copperhead 12 bushing |
You can remove the prop shaft seal but not the brass bushing. It needs to be tapped out a little bit all the way around till its out. |
|
| Author: | cmiller73 [ Fri Aug 17, 2012 7:20 am ] |
| Post subject: | Re: copperhead 12 bushing |
If you have questions, call Gil at Copperhead. He'll tell you what you need to do to get it fixed. |
|
| Author: | grasshopper [ Fri Aug 17, 2012 4:31 pm ] |
| Post subject: | Re: copperhead 12 bushing |
I will call gil .. ment 2 today but working a shut down no time to |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|