MudmotorTalk.com
http://www.mudmotortalk.com/mmt_v2/

Trim on a mudbuddy 45 mag
http://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=65126		 Page 1 of 1
Author:  Ole Boudreaux [ Fri Dec 25, 2015 1:46 pm ]
Post subject:  Trim on a mudbuddy 45 mag
I get done hunting yesterday. Load up the boat trim the motor up. As I'm strapping down the boat the trim comes on and won't stop. I had to disconnect the battery to stop. Any ideas? Thanks happy holiday
Author:  flint87 [ Fri Dec 25, 2015 1:47 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Gotta be in your trim switch


Sent from my iPhone using Tapatalk
Author:  Ole Boudreaux [ Fri Dec 25, 2015 1:55 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Can I get that part at napa? Or is it a mud buddy part only?
Author:  JD145 [ Fri Dec 25, 2015 2:01 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
You may be able to find one Somewhere else not sure, just call boatDR, he can fix you up.
Author:  lunacris [ Fri Dec 25, 2015 2:02 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
get the new style trim switch. i just upgraded mine, its wonderful.
Author:  Gunshinestate407 [ Fri Dec 25, 2015 2:29 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Call boat dr. He had 2 new ones on my door step in a couple days.


Sent from my iPhone using Tapatalk
Author:  flint87 [ Fri Dec 25, 2015 4:48 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Disregard my last post. I just went full fucking retard talking about a clutch switch. This is why I drive a godevil... That and I'm too poor for a fancy mud buddy.


Sent from my iPhone using Tapatalk
Author:  deadbird8 [ Sun Dec 27, 2015 3:05 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Author:  DmaxHunter [ Sun Dec 27, 2015 4:10 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Author:  Ole Boudreaux [ Thu Jan 07, 2016 6:30 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Ok I changed trim switch,both relays, and both fuses. Still doesn't work. I think it's the motor. Can I buy a motor of eBay for 130$ or do I need to replace everything which would cost about 700$. Thanks for the help.
Author:  DmaxHunter [ Thu Jan 07, 2016 6:54 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
A couple have bought just the motor from Amazon or eBay, they posted the part number. Maybe someone will chime in
Author:  DENNYEDWARDS [ Sun Jan 17, 2016 10:13 am ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Amazon .com Mercury replacement trim motor. It is a direct replacement #809885A $122. Magnets came unglued in Motors case and locked it up in mine. Save your drive pin that goes in to pump, otherwise you may have to shorten the one that comes with motor. Will have to add fluid to resivour, because you will loose some when removing it from pump housing. They are self bleeding so you may hook it up to a battery, and run the cylinder up and down a few times to get air out of it. We clamp them up in vise and do this. Reverse pump wires to battery to reverse motor for up and down. Check res. level before installing back on motor. Saves much $$ over one from MB.
Author:  lunacris [ Sun Jan 17, 2016 11:44 am ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Author:  lunacris [ Sun Jan 17, 2016 11:52 am ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Author:  Migrator [ Sun Jan 17, 2016 2:34 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Chris, is this the new mercury trim switch that comes on the HDR's? If so I like that switch. Should hold up much better than the old ones.


Sent from my iPhone using Tapatalk
Author:  lunacris [ Sun Jan 17, 2016 2:52 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
it is.... i love how its recessed into the handle. the new clutch switch is also a big upgrade.
Author:  DmaxHunter [ Sun Jan 17, 2016 10:08 pm ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Luna are the parts online, or did you call and order
Author:  lunacris [ Mon Jan 18, 2016 8:18 am ]
Post subject:  Re: Trim on a mudbuddy 45 mag
Andy hooked me up
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/