|
|
FAQ
• Login
|
|
It is currently Wed Apr 17, 2024 10:08 pm
|
|
Page 1 of 1
|
[ 6 posts ] |
|
| Author |
Message |
|
d_white
MMT Addict
Joined: Sat May 02, 2009 1:11 am
Posts: 549
|
 Bad zert? Do zerts go bad? Greased my HDR shaft a couple of days ago. Let the excess bleed out. Ran some this weekend and then noticed this. Also, does it look like water is mixed with the grease? Will replacing the fitting likely fix this? It feels like it's screwed in tight and the grease seemed to have come out the top.
Sent from my iPhone using Tapatalk
|
| Mon Mar 27, 2017 9:31 am |
|
|
|
Smoke
MMT 1000 Club
Joined: Fri Jan 23, 2009 1:27 pm
Posts: 1095
Location: SW Michigan
|
Re: Bad zert? Sometimes the ball will stick down and allow grease out the tip. Did you grease it the proper way by removing the screw in the outdrive casting and removing the nut on the prop end of the shaft? You may have over greased it and had to much pressure in the outdrive tube? If you do that to many times you'll blow the seals out both ends and have a damn mess in the belt box.
_________________
1854 Prodigy Open
HDR/Stage 3 mods
Prodigy Boats Pro Staff
BPS Swamp Staff Member
Blackwater Marine LLC.
Quote classic by rangerp: "Red seemed to be enjoying herself, and I assume by the look on her face was about to hit the high-note and throw a locate as she treed the possum."
|
| Mon Mar 27, 2017 10:06 am |
|
|
|
d_white
MMT Addict
Joined: Sat May 02, 2009 1:11 am
Posts: 549
|
Re: Bad zert? I removed the upper screw to vent it but not the prop nut
Sent from my iPhone using Tapatalk
|
| Mon Mar 27, 2017 11:23 am |
|
|
|
Smoke
MMT 1000 Club
Joined: Fri Jan 23, 2009 1:27 pm
Posts: 1095
Location: SW Michigan
|
Re: Bad zert? Did you let the motor run while in gear for a bit after greasing with the screw out? It will work out a bit of the grease if you over filled it. Most tend to over fill while greasing, that's why I ask.
_________________
1854 Prodigy Open
HDR/Stage 3 mods
Prodigy Boats Pro Staff
BPS Swamp Staff Member
Blackwater Marine LLC.
Quote classic by rangerp: "Red seemed to be enjoying herself, and I assume by the look on her face was about to hit the high-note and throw a locate as she treed the possum."
|
| Tue Mar 28, 2017 4:34 am |
|
|
|
Smoke
MMT 1000 Club
Joined: Fri Jan 23, 2009 1:27 pm
Posts: 1095
Location: SW Michigan
|
Re: Bad zert? .
_________________
1854 Prodigy Open
HDR/Stage 3 mods
Prodigy Boats Pro Staff
BPS Swamp Staff Member
Blackwater Marine LLC.
Quote classic by rangerp: "Red seemed to be enjoying herself, and I assume by the look on her face was about to hit the high-note and throw a locate as she treed the possum."
|
| Tue Mar 28, 2017 4:34 am |
|
|
|
CypressCritter
MMT F.E.
Joined: Tue Aug 26, 2014 10:36 am
Posts: 822
Location: Jefferson TX
|
Re: Bad zert? Bad zert! Cheap easy fix. A zert should not let grease come out of it. Be sure when greasing, wipe off zert and grease gun tip to clean it of foreign material. That could also keep the little ball from sealing off after greasing. Just takes 1 little grain of sand and leaky-leaky.
_________________
SEAARK FX 2472 CC Merc 150HP 4Stroke(CypressCadillac)
Uncle J Custom - 19x54 CC Skiff w/40XD GTR
|
| Tue Mar 28, 2017 8:03 am |
|
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 89 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
