| MudmotorTalk.com http://www.mudmotortalk.com/mmt_v2/ |
|
| brother breaux outboard build http://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=5&t=40529 |
Page 1 of 1 |
| Author: | swampfox1 [ Wed May 08, 2013 7:52 am ] |
| Post subject: | brother breaux outboard build |
finally got her rigged with 90 hp yamaha. b&b 19ft x 60 with v bow 23 in. sides with 6in catwalks center console she ran like a scalded dog at 38 knots with 20 gallons fuel. super stable and very happy with handling perforormance. need some advice though. she was built with mud boat style trim tabs on each transom corner. the more i try to trim her up while underway the more bow is shoved downward. its almost like an opposite effect. any corrective thoughts on this would be appreciated. would cutting tabs off be my cure? having trouble with pic post but can send pic to someone on here via i phone if they will post it. swampfox |
|
| Author: | swampfox1 [ Wed May 08, 2013 7:59 am ] |
| Post subject: | Re: brother breaux outboard build |
well, any any thoughts on trim ? |
|
| Author: | krogers [ Wed May 08, 2013 8:08 am ] |
| Post subject: | Re: brother breaux outboard build |
ImageUploadedByTapatalk1368022062.470066.jpg |
|
| Author: | DD [ Wed May 08, 2013 8:11 am ] |
| Post subject: | Re: brother breaux outboard build |
are you talking about trimming the motor up or the tabs? |
|
| Author: | krogers [ Wed May 08, 2013 8:11 am ] |
| Post subject: | Re: brother breaux outboard build |
That dude builds a fine boat, sonbitch. not sure how to help with the trim. heres a pic of the rear of my river boat. flat bottom small tabs in back, but i do not have the problem with the boat diving when i trim up |
|
| Author: | BayouBuster [ Wed May 08, 2013 8:16 am ] |
| Post subject: | Re: brother breaux outboard build |
Try bending the tabs up. |
|
| Author: | doubleBanded [ Wed May 08, 2013 9:37 am ] |
| Post subject: | Re: brother breaux outboard build |
Boat looks good! X2 on trim tabs |
|
| Author: | swampfox1 [ Thu May 09, 2013 6:30 am ] |
| Post subject: | Re: brother breaux outboard build |
i think i figured it out . had motor hung too low and cavitation plate was below bottom of transom. unbolted and raised motor to 3rd bolt hole and gonna try out today. anyone ever dealt with this on outboard? swamp.... |
|
| Author: | swampfox1 [ Thu May 09, 2013 6:31 am ] |
| Post subject: | Re: brother breaux outboard build |
i think i figured it out . had motor hung too low and cavitation plate was below bottom of transom. unbolted and raised motor to 3rd bolt hole and gonna try out today. anyone ever dealt with this on outboard? swamp.... |
|
| Author: | krogers [ Thu May 09, 2013 10:53 am ] |
| Post subject: | Re: brother breaux outboard build |
def dont want the cav plate below the bottom of the boat, if anything hang an inch or two above. should be aite. send me a couple pics to post. |
|
| Author: | swampfox1 [ Thu May 09, 2013 10:58 am ] |
| Post subject: | Re: brother breaux outboard build |
10-4 |
|
| Author: | duckhunter888 [ Fri May 10, 2013 5:21 am ] |
| Post subject: | Re: brother breaux outboard build |
Hey Swampfox, please post a few more pics of your boat, especially the front end, is that a mod v into a flat?,looks good |
|
| Author: | cajundan [ Fri May 10, 2013 6:36 am ] |
| Post subject: | Re: brother breaux outboard build |
Jackplate. It gives you setback and rise. Sent from my C771 using Tapatalk 2 |
|
| Author: | swampfox1 [ Fri May 10, 2013 8:46 am ] |
| Post subject: | Re: brother breaux outboard build |
boat is at crab dock and will be there this afternoon to take some more pics. yes it is modv into flat. have contemplated jack plate but am broke after hydro-steering and motor purchase last week. gonna try out adjusted cav-plate today. krogers, i am gonna send u some pics via phone. swamp...... |
|
| Author: | krogers [ Fri May 10, 2013 9:34 am ] |
| Post subject: | Re: brother breaux outboard build |
ImageUploadedByTapatalk1368199983.636597.jpg ImageUploadedByTapatalk1368200000.044612.jpg ImageUploadedByTapatalk1368200010.787130.jpg |
|
| Author: | krogers [ Fri May 10, 2013 9:35 am ] |
| Post subject: | Re: brother breaux outboard build |
ImageUploadedByTapatalk1368200058.461362.jpg ImageUploadedByTapatalk1368200068.615123.jpg Good talkin with you, swampfox. Badass boat too. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|