|
FAQ
• Login
|
|
It is currently Wed May 14, 2025 6:08 am
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Author |
Message |
TEXLADUCKSLAYER
MMT Member
Joined: Sun Jan 18, 2009 5:32 pm Posts: 21
|
 RPM and Speed question
I have a light modded 23lt and I am turning 3850 in water with a 9x7 running 22mph and turning a 9x6 4000 running 22mph....any ideas???? Am I topped out or can I get more?
|
Wed Aug 03, 2011 1:31 pm |
|
 |
kibb
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:58 pm Posts: 2731 Location: Lafayette, LA
|
 RPM and Speed question
With those props I doubt you will get anything higher. You are probably running about 20-21 at 3600 and then that. I think you are at the top of the curve right now.
_________________ 1644 WeldCraft / 27 GDLT Ranger R71 / 125 Merc
|
Wed Aug 03, 2011 3:10 pm |
|
 |
TEXLADUCKSLAYER
MMT Member
Joined: Sun Jan 18, 2009 5:32 pm Posts: 21
|
 Re: RPM and Speed question
So would getting someone such as Hopkins to tune up a prop to say 9x8 or 9x9 help any?
|
Wed Aug 03, 2011 8:00 pm |
|
 |
kibb
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:58 pm Posts: 2731 Location: Lafayette, LA
|
 RPM and Speed question
Might wanna wait and see if someone with a similar motor chimes in.
_________________ 1644 WeldCraft / 27 GDLT Ranger R71 / 125 Merc
|
Wed Aug 03, 2011 8:03 pm |
|
 |
TEXLADUCKSLAYER
MMT Member
Joined: Sun Jan 18, 2009 5:32 pm Posts: 21
|
 Re: RPM and Speed question
Ok man, appreciate it. I did go run it again today and added some octane boost and got 3950 and bumped 23 a couple times with 2 of us in the boat...only reason I tried that was I was having a detonation/preignition problem and was trying the octane boost for that problem.
|
Wed Aug 03, 2011 8:14 pm |
|
 |
Woodiebuster
MMT Elite Member
Joined: Wed Mar 03, 2010 7:00 pm Posts: 6060 Location: Choudrant, La
|
 Re: RPM and Speed question
What size boat is it on?
Without doing more mods it sounds like you are about peaked out. What have you done to it?
_________________ CSM Custom 18x42 Battleship with a 36 PD beating you to the hole My Rig (Old Motor) viewtopic.php?f=5&t=45193
(New Motor) viewtopic.php?f=5&t=54733 Stumps Fear Me
|
Wed Aug 03, 2011 8:23 pm |
|
 |
TEXLADUCKSLAYER
MMT Member
Joined: Sun Jan 18, 2009 5:32 pm Posts: 21
|
 Re: RPM and Speed question
Woodie, it is on a 1652 riveted flat with frog spit on bottom. decked heads 15, bored 30 over, polished and 3 angle valve grind, 35 carb, twin exhaust, high flow s&b air filter.
|
Wed Aug 03, 2011 8:31 pm |
|
 |
|
|
Page 1 of 1
|
[ 7 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 110 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|