| Author |
Message |
|
Machinist5381
MMT Member
Joined: Sat Feb 02, 2013 10:39 pm
Posts: 47
Location: Houma, Louisiana
|
 PD Cam How hard is it to install a new BPS Cam in my 08 PD? I shaved my heads with no problems and I was woundering if I really need to bring it to someone or is it something I can do myself!!!
_________________
36HP Prodrive W/
Mods
18'X48" Prodrive Haul
|
| Thu Jul 04, 2013 10:49 pm |
|
|
|
CJB
MMT Elite Member
Joined: Tue Sep 13, 2011 11:46 am
Posts: 5216
Location: Across the Bayou, LA
|
Re: PD Cam Gotta pull the block off the frame for starters.
_________________
35 GTR - 1754 Extreme
|
| Fri Jul 05, 2013 8:04 am |
|
|
|
tchauvin
MMT 1000 Club
Joined: Wed Jul 13, 2011 6:23 pm
Posts: 4898
Location: Bourg LA
|
Re: PD Cam Not bad, take ur time and u will be ok. Do it easy in a day...
|
| Fri Jul 05, 2013 12:23 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: PD Cam An 08 might give you a little trouble. some motors that old don't like to come apart. If you took care of it and sprayed it down with WD40 or some sort of corrosion inhibitor on a regular basis than you should be fine. Some times the clutch and spine adapter can be a bitch to get off. I'd soak the down now.
Also its a good idea to go ahead and get new PTO oil seal. Remove the old one before pulling the crank case/sump so that you can clean the rust off the PTO/crank shaft before dragging it across your bearings.
There's more but my lunch is getting cold.
|
| Fri Jul 05, 2013 12:44 pm |
|
|
|
Machinist5381
MMT Member
Joined: Sat Feb 02, 2013 10:39 pm
Posts: 47
Location: Houma, Louisiana
|
Re: PD Cam I helped my buddy change his clutch the other day and I soak my motor in WD-40 everytime I use it so I should be fine. Where is a good place to get a cam?
_________________
36HP Prodrive W/
Mods
18'X48" Prodrive Haul
|
| Fri Jul 05, 2013 2:29 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: PD Cam All depends on what you want your motor to do?
|
| Fri Jul 05, 2013 2:54 pm |
|
|
|
flatboat
MMT Pro Member
Joined: Sun Mar 08, 2009 7:22 pm
Posts: 401
|
Re: PD Cam
|
| Fri Jul 05, 2013 8:15 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: PD Cam
|
| Fri Jul 05, 2013 10:03 pm |
|
|
|
Machinist5381
MMT Member
Joined: Sat Feb 02, 2013 10:39 pm
Posts: 47
Location: Houma, Louisiana
|
Re: PD Cam
_________________
36HP Prodrive W/
Mods
18'X48" Prodrive Haul
|
| Fri Jul 05, 2013 11:00 pm |
|
|
|
flatboat
MMT Pro Member
Joined: Sun Mar 08, 2009 7:22 pm
Posts: 401
|
Re: PD Cam
|
| Sat Jul 06, 2013 3:45 am |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: PD Cam  dats right!
|
| Mon Jul 08, 2013 4:59 pm |
|
|
|
Will
MMT Elite Member
Joined: Fri Jul 08, 2011 1:54 pm
Posts: 8133
|
Re: PD Cam
_________________
Before the internet, the majority of the village idiots stayed in their villages.
|
| Mon Jul 08, 2013 7:03 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: PD Cam @ sardines
|
| Mon Jul 08, 2013 8:13 pm |
|
|
|
Will
MMT Elite Member
Joined: Fri Jul 08, 2011 1:54 pm
Posts: 8133
|
Re: PD Cam Well did you do it?
_________________
Before the internet, the majority of the village idiots stayed in their villages.
|
| Thu Aug 01, 2013 1:37 pm |
|
|
|
