Author |
Message |
GootJune
MMT Pro Member
Joined: Mon Apr 15, 2013 9:28 am Posts: 52 Location: Panama City, FL
|
 16/46HD GTR 25
Well, I know there's a couple of reviews on these. But figured I would give input to everyone on what I have learned so far.
Boat has a completely open floor plan. Just the necessities that Gatortail adds such as as the 4' front deck and I opted for the hunt deck as well.
Me and a buddy I ran 24 bumping 25 in deep water. Was a little bumpy and going into the wind. Me by myself I ran 26 constantly in deep water. I never got it shallow when I had the GPS on, but did seem to notice a little bit of an increase when I got in about 2' of water.
Straight from the factory the RPM's are about 3720 WOT. I've read that it is a pain in the ass to adjust the governor and get the idle to both cooperate and that it's not really worth the trouble for a couple hundred RPM's. SO I am leaving the governor the way it is.
There has also been problems with the motor dying when first kicking it in gear and trying to feather the throttle a little to keep it from dying, adjusting the idle a little higher solved this problem for the most part. I also noticed it helped a little after the first oil change at around 20 hours and the first shaft grease change at around 15 hours.
I've got a little over 25 hours and still like it. I just installed a 20" LED light bar on the front. Haven't gotten to test it out yet, but this where I got it from. Gatortail already had the wires ran up front so all I did was mount a cigarette lighter plug to the front of the boat, now I have the option to plug any 12 volt DC adapter to the front. I plan on putting some hydro turf down sometime soon, but may have to wait till after duck season.
image (2).jpeg
image (1).jpeg
image (3).jpeg
You do not have the required permissions to view the files attached to this post.
_________________ 1646 GTB • 25 GTR EFI
|
Tue Aug 13, 2013 7:58 am |
|
 |
Jw261
MMT Pro Member
Joined: Sat Oct 22, 2011 12:20 pm Posts: 96 Location: Lower Alabama
|
 Re: 16/46HD GTR 25
Just got nearly the same setup this summer and love it. I had the hydroturf installed at GT. It's a good running little boat. I'm getting around the same speeds with mine.
|
Tue Aug 13, 2013 8:04 am |
|
 |
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
 Re: 16/46HD GTR 25
Thats the speeds I'm seeing in similar conditions. Nice rig!
|
Tue Aug 13, 2013 8:37 am |
|
 |
eljefe
MMT Elite Member
Joined: Thu Jan 13, 2011 7:32 am Posts: 5210 Location: Beaumont Texas
|
 Re: 16/46HD GTR 25
Its funny how a foot or 2 longer will give you an additional 2 mph..... it is important to get these boats as flat as possible when on plane...... try and add a little more weight up front and see if that dosent put you in the 27-28 in deeper water.....mine is running a pretty constant 27 in deeper water and 28-29 in shallow water.
_________________ You can't see the sunrise if your eyes are closed. dying aint much of a livin....
Black ops IITX marshstalker
1840 WC www.wccustomboats.com fuel injected 25 GTR
|
Tue Aug 13, 2013 8:46 am |
|
 |
Swamp dog
MMT Pro Member
Joined: Wed May 15, 2013 1:55 pm Posts: 196 Location: Gonzales
|
 Re: 16/46HD GTR 25
Sweet ill rig
_________________ 18x46 dfou custom with a 35GTR stage 1
|
Tue Aug 13, 2013 10:59 am |
|
 |
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm Posts: 1018 Location: DA HAVEN FL,
|
 Re: 16/46HD GTR 25
Good looking rig. Do you hunt deer point much?
_________________ EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
Tue Aug 13, 2013 1:33 pm |
|
 |
GootJune
MMT Pro Member
Joined: Mon Apr 15, 2013 9:28 am Posts: 52 Location: Panama City, FL
|
 Re: 16/46HD GTR 25
Yeah we hunt there quite a bit, especially early on in the season. We have a couple new spots we are going to scout out there, along with some other lakes we want to check out.
Your skiff is going to put up some nice numbers with that 35 on it. I'd like to see it on the water when you get it.
_________________ 1646 GTB • 25 GTR EFI
|
Tue Aug 13, 2013 1:58 pm |
|
 |
Greenmachine
MMT F.E.
Joined: Tue Feb 19, 2013 10:31 am Posts: 778
|
 Re: 16/46HD GTR 25
Keep it longer than 2 weeks
|
Tue Aug 13, 2013 1:59 pm |
|
 |
GootJune
MMT Pro Member
Joined: Mon Apr 15, 2013 9:28 am Posts: 52 Location: Panama City, FL
|
 Re: 16/46HD GTR 25
Got it late June, so working on 2 months. Don't plan on getting rid of it anytime within the next few years unless I get in bad bind.
_________________ 1646 GTB • 25 GTR EFI
|
Tue Aug 13, 2013 2:04 pm |
|
 |
eljefe
MMT Elite Member
Joined: Thu Jan 13, 2011 7:32 am Posts: 5210 Location: Beaumont Texas
|
 Re: 16/46HD GTR 25
June is a bad month to get a boat completed....1st of april is mo betta 
_________________ You can't see the sunrise if your eyes are closed. dying aint much of a livin....
Black ops IITX marshstalker
1840 WC www.wccustomboats.com fuel injected 25 GTR
|
Tue Aug 13, 2013 2:07 pm |
|
 |
calphil
MMT 1000 Club
Joined: Sun Feb 26, 2012 10:49 pm Posts: 1715 Location: Kingwood,TX
|
 Re: 16/46HD GTR 25
Nice boat and seems pretty average as to what everyone else's speeds are especially since leaving governor set low ..
I'm hopin to hit the same once I get my boat but I plan to bump the RPM's up to 4000 to maybe help a little
Sent from... who cares..
_________________ 1744 WC Custom 25 GTR
|
Tue Aug 13, 2013 3:01 pm |
|
 |
GootJune
MMT Pro Member
Joined: Mon Apr 15, 2013 9:28 am Posts: 52 Location: Panama City, FL
|
 Re: 16/46HD GTR 25
Yeah, I am not that worried about it. All that trouble I have heard about for another MPH or two. Ehh, I am never in that much of hurry to get anywhere.
_________________ 1646 GTB • 25 GTR EFI
|
Tue Aug 13, 2013 3:07 pm |
|
 |
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm Posts: 1018 Location: DA HAVEN FL,
|
 Re: 16/46HD GTR 25
_________________ EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
Tue Aug 13, 2013 4:08 pm |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: 16/46HD GTR 25
_________________ 1754 GTB / 35 GTR
|
Tue Aug 13, 2013 4:37 pm |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: 16/46HD GTR 25
_________________ 1754 GTB / 35 GTR
|
Tue Aug 13, 2013 4:40 pm |
|
 |
Podcast
MMT 1000 Club
Joined: Fri Dec 09, 2011 12:33 pm Posts: 1363 Location: Friggin cold up here
|
 Re: 16/46HD GTR 25
_________________ Wildberry "Between You, Will, DUCK HEARSE, and PODCAST I have trouble reading anything on here" 23GTR stage 2 by Calen pushin a 1746 Kliebert
|
Tue Aug 13, 2013 5:18 pm |
|
 |
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm Posts: 1018 Location: DA HAVEN FL,
|
 Re: 16/46HD GTR 25
Podcast, I just noticed your signature.... I .. I.. don't know what to say. It means more to me than my first 500 posts 
_________________ EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
Tue Aug 13, 2013 7:51 pm |
|
 |
cajun1085
MMT Pro Member
Joined: Fri May 10, 2013 2:57 pm Posts: 183 Location: Silver Spring, MD
|
 Re: 16/46HD GTR 25
Im getting the about the same speeds. RPMs 3650. I have a little more weight in mine with trolling motor setup. Today the best speeds I got was 22.9 with wife and I with a lot of fishing gear, 2 icechest, 9 gal of fuel. What is your idle set at? Mine likes to die and I have to feather it. My idle is set at 900 in forward.
You do not have the required permissions to view the files attached to this post.
_________________ GTB 1646 w/HD, Boat Blind-25GTR
SOUTHEAST GATORTAIL
|
Tue Aug 13, 2013 7:54 pm |
|
 |
GootJune
MMT Pro Member
Joined: Mon Apr 15, 2013 9:28 am Posts: 52 Location: Panama City, FL
|
 Re: 16/46HD GTR 25
_________________ 1646 GTB • 25 GTR EFI
|
Tue Aug 13, 2013 8:19 pm |
|
 |
GootJune
MMT Pro Member
Joined: Mon Apr 15, 2013 9:28 am Posts: 52 Location: Panama City, FL
|
 Re: 16/46HD GTR 25
_________________ 1646 GTB • 25 GTR EFI
|
Tue Aug 13, 2013 8:23 pm |
|
 |
lucecr
MMT 1000 Club
Joined: Sun Jan 30, 2011 9:26 am Posts: 1629
|
 Re: 16/46HD GTR 25
_________________ InstaGator 16.5' x 46" 25efi GTR. Running 30+ SOLD!!!!
dillakilla12 wrote:
I just passed out bc of the blood rush to my penis! Where the fugg can I get a transom like that!?
|
Tue Aug 13, 2013 9:26 pm |
|
 |
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm Posts: 1018 Location: DA HAVEN FL,
|
 Re: 16/46HD GTR 25
_________________ EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
Wed Aug 14, 2013 4:40 am |
|
 |
Podcast
MMT 1000 Club
Joined: Fri Dec 09, 2011 12:33 pm Posts: 1363 Location: Friggin cold up here
|
 Re: 16/46HD GTR 25
_________________ Wildberry "Between You, Will, DUCK HEARSE, and PODCAST I have trouble reading anything on here" 23GTR stage 2 by Calen pushin a 1746 Kliebert
|
Wed Aug 14, 2013 8:35 am |
|
 |
Wildberry
MMT 1000 Club
Joined: Sun Apr 22, 2012 6:17 pm Posts: 1018 Location: DA HAVEN FL,
|
 Re: 16/46HD GTR 25
 keep up the good pictures !!
_________________ EMF 16x42, 3/16 skiff, 35 GTR Stage 0
|
Wed Aug 14, 2013 9:13 am |
|
 |
cajun1085
MMT Pro Member
Joined: Fri May 10, 2013 2:57 pm Posts: 183 Location: Silver Spring, MD
|
 Re: 16/46HD GTR 25
Well striped everything out my boat and ran it for the first time by myself today! Not bad at all! 27.2mph down river haha! 26.8 going up!
You do not have the required permissions to view the files attached to this post.
_________________ GTB 1646 w/HD, Boat Blind-25GTR
SOUTHEAST GATORTAIL
|
Wed Aug 14, 2013 6:57 pm |
|
 |
cmk07c
MMT Addict
Joined: Thu Jul 21, 2011 9:11 am Posts: 556 Location: Metairie, LA
|
 Re: 16/46HD GTR 25
Nice that's moving. You ran it loads with adults yet?
|
Wed Aug 14, 2013 7:33 pm |
|
 |
cajun1085
MMT Pro Member
Joined: Fri May 10, 2013 2:57 pm Posts: 183 Location: Silver Spring, MD
|
 Re: 16/46HD GTR 25
Wife and I cruising 25-25.5. Fishing load with 2 ice chest 23-24. 3 people 21. All were in 2-3 foot of water. It gets the job done. Yea another 5 mph would be nice, but I had a budget. It was either a few more hunting accessories or the 35.
_________________ GTB 1646 w/HD, Boat Blind-25GTR
SOUTHEAST GATORTAIL
|
Wed Aug 14, 2013 8:26 pm |
|
 |
TPerkins
MMT 1000 Club
Joined: Wed Jan 02, 2013 12:59 pm Posts: 1793 Location: Clear Lake, Tx
|
 Re: 16/46HD GTR 25
Were the 3 person load speeds above with the boat stripped, or with fish/hunt load?
|
Thu Aug 15, 2013 8:31 am |
|
 |
cajun1085
MMT Pro Member
Joined: Fri May 10, 2013 2:57 pm Posts: 183 Location: Silver Spring, MD
|
 Re: 16/46HD GTR 25
_________________ GTB 1646 w/HD, Boat Blind-25GTR
SOUTHEAST GATORTAIL
|
Thu Aug 15, 2013 9:56 am |
|
 |
cmk07c
MMT Addict
Joined: Thu Jul 21, 2011 9:11 am Posts: 556 Location: Metairie, LA
|
 Re: 16/46HD GTR 25
Like seeing good reviews like these!
|
Thu Aug 15, 2013 10:03 am |
|
 |
|