| Author |
Message |
|
boatguy
MMT Pro Member
Joined: Mon Dec 05, 2016 11:59 am
Posts: 219
Location: Panhandle of Florida
|
 Washer? Took my prop off to clean shaft and threads... Does the washer go on before for the prop or after the prop. 4400 HDR Mud Buddy
_________________
Lead, Follow or Get The Hell Out Of The Way!!!!
1754 Gator Trax Hybrid, Hunt Deck ,with MB 4400 Black Death HDR, Duck Slaying, Mud Slingin Machine!!!
|
| Wed Apr 04, 2018 4:53 am |
 
|
|
|
Koondog62
MMT Pro Member
Joined: Thu Jul 20, 2017 6:23 am
Posts: 129
|
Re: Washer? On my gatortail it is after and it is shaped to hold pressure on nut and prop. Can not remember the name of the washer.
|
| Wed Apr 04, 2018 7:08 am |
|
|
|
Russ
MMT 1000 Club
Joined: Mon Dec 31, 2012 11:07 pm
Posts: 4820
Location: West Monroe, LA
|
Re: Washer? So it's a "pressure washer"?
#CFFITR
#TheGhostBoat
#whoneedsphysicsihaveamudmotor
|
| Wed Apr 04, 2018 7:47 am |
|
|
|
Koondog62
MMT Pro Member
Joined: Thu Jul 20, 2017 6:23 am
Posts: 129
|
Re: Washer?
|
| Wed Apr 04, 2018 8:50 am |
|
|
|
Russ
MMT 1000 Club
Joined: Mon Dec 31, 2012 11:07 pm
Posts: 4820
Location: West Monroe, LA
|
Re: Washer? I wasn't being helpful, just said it outloud, chuckled, figured I let others have a potential chuckle over a stupid pun.
Back on topic. The washer needed there isn't a big deal, as long as it's the right thickness. The op has the washer, just wanted to confirm location for install. You done solved that riddle for him.
#CFFITR
#TheGhostBoat
#whoneedsphysicsihaveamudmotor
|
| Wed Apr 04, 2018 10:17 am |
|
|
|
BlueShamu
MMT Elite Member
Joined: Mon Feb 06, 2012 6:13 pm
Posts: 5605
Location: D'town, LA
|
Washer? I'm not familiar with the washer at all...but, if it's like you describe, that's called a belleville washer. It's cupped to give additional compressional forces to keep a nut in place and keep tension on the mechanical joint.
If it is truly a Belleville washer, they typically are placed under the nut. They are dish/cone shaped. The smaller surface should be against the nut.
|
| Wed Apr 04, 2018 10:38 am |
|
|
|
Koondog62
MMT Pro Member
Joined: Thu Jul 20, 2017 6:23 am
Posts: 129
|
Re: Washer?
|
| Wed Apr 04, 2018 10:56 am |
|
|
|
Koondog62
MMT Pro Member
Joined: Thu Jul 20, 2017 6:23 am
Posts: 129
|
Re: Washer?
|
| Wed Apr 04, 2018 10:59 am |
|
|
|
boatguy
MMT Pro Member
Joined: Mon Dec 05, 2016 11:59 am
Posts: 219
Location: Panhandle of Florida
|
Re: Washer? Ok,, so I took the BB off to put the new Hammer blade on... this washer will not fit inside the Hammer blade. I put the Hammer blade on the shaft then go to put the washer on and the washer is slightly bigger than the recessed area of the prop... Is this common... I wound up sanding the diameter of the washer down a bit so it would fit in the recessed hole of the Hammer prop... ???
_________________
Lead, Follow or Get The Hell Out Of The Way!!!!
1754 Gator Trax Hybrid, Hunt Deck ,with MB 4400 Black Death HDR, Duck Slaying, Mud Slingin Machine!!!
|
| Thu Apr 05, 2018 5:08 pm |
|
|
|
Old School
MMT 1000 Club
Joined: Thu Dec 17, 2009 9:44 pm
Posts: 3067
Location: Earth
|
Re: Washer? Boat guy is a cool handle
Sent from my iPhone using Tapatalk
_________________
Gator tail
|
| Fri Apr 06, 2018 6:56 pm |
|
|
|
