Author |
Message |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) 20x50 WC Custom // Go Devil 40 FNR Review
Here is the review for my new WC Custom rig. A little lengthy but I think I covered it all.
20x50 WC Custom hull paired with new 40 horse Go Devil FNR motor (bone stock) Base load (fishing season): 9 gallon fuel tank, Wetsounds Surge 10 sound bar (20 lbs.), Wetsounds AS-10" sub with amplifier (29 lbs), Minn Kota 54" 55 lb trolling motor with deep cycle marine battery all positioned in front of boat. Standard crank battery and Wetsounds Surge 6 soundbar (13 lbs.) in rear. I did my own rigging on fishfinder, light bar and stereo install.
Conditions / Terrain: Marsh; silt bottom cat-tail flats Average Depth: 6"-4' Wind gusts: 5-10 mph Elevation: 4,551' Performance - Keep in mind I'm losing around 15-20% for altitude, equates to around 3-5 hp (which BLOWS coming from sea level) so this will be a little skewed for most of ya'll.
Base load + myself (220 lbs); Depth: "ideal": Top end 27 mph @~4300 rpms
Base load + myself (220 lbs) + 1 body (~200 lbs) + fishing gear + RTIC 65 cooler; Depth: "ideal" Top end 25-26 mph @3950-4150 rpms
Overall this hull is a tank and carries the load well. The goal with the 20' hull was to see speeds and RPM's stay more consistent with the more I load it down. I knew I'd lose a couple mph on the top end with longer hull but load performance is what I wanted to see. Duck season will be the true test for this. Altitude being the other factor, there's a definite 2-4 hp loss at least up here but overall performance so far my expectation's met.
Drafting shallow shallow was a goal achieved. This hull drafts shallower than any other hull I've seen or ran. Combined with the mid range power from the 40 this combo will dig and get up on plane quick from a complete stop in around 6" of water/hard silt bottom, looked up and found myself running border line air boat territory. Really impressed with the hull draft.
Motor Review: I dig the hell outta the Go Devil FNR frame, I see a lot of haters on the manual trim. The relocation of the drop lever is what made manual trim a definite preference for me. Once trim is set your set and the drop lever is easily accessible to drop the prop for quick bite whether it be for reverse or just getting out of tricky spots in FWD. The configuration with the controls on the new FNR frame is what ultimately had me sold. The UX flow of the motor overall IMO has everything else out there beat rn, feel confident saying I can do things with this motor that I wouldn't be able to do with a Pro Drive, GTR, or Mud Buddy.
Only downside or negative I'm seeing- with trim set just right, in the sweet spot for best speed, motor tends to want to fight the hell outta me, pulling strong to my left side. Getting weight distribution perfect helps but doesn't fix it completely. I'm also gonna take a second look to make sure motor is perfect center on transom, it may not be completely perfect rn but if its off at all its not by much.
Briggs 40 - Mid range power is no joke. This block is a definite 'step up' for Briggs IMO as far as a pure factory built stock block.
Builder review: Not here to give WC a bad rap at all. Overall couldnt be more pleased with this hull, structurally it beats anything else I coulda asked for. Purely constructive feedback- if I were to offer up anything that could be improved upon with builder I'd say better communication. With the final wrap of my build there were a few minor things that I think were either rushed and/or overlooked. I'll spare details but when you're paying this kind of high dollar for a rig its a huge disappoint finally getting your boat to find small things here or there that were overlooked, purely constructive criticism and really only narrows down to 2 or 3 small minor things, overall im pleased with my boat.
You do not have the required permissions to view the files attached to this post.
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Mon Apr 08, 2019 9:32 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Sent from my iPhone using Tapatalk
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Mon Apr 08, 2019 10:02 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Will C
MMT Sponsor
Joined: Fri Jan 10, 2014 1:16 pm Posts: 2107 Location: Gladewater TX
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Looks Badass
|
Mon Apr 08, 2019 10:31 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Are you in law enforcement or something of that nature?
_________________ Refurbishing a Prodrive
|
Mon Apr 08, 2019 11:11 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Very nice boat and very good review bro. Hope you enjoy it for years to come. I found that the tiller torque with my GTR was horrible at the beginning but I don’t know if I just got used to it or if it eventually worked it’s way out
|
Mon Apr 08, 2019 12:41 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Mon Apr 08, 2019 1:30 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Mon Apr 08, 2019 1:38 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
You do not have the required permissions to view the files attached to this post.
_________________ Refurbishing a Prodrive
|
Mon Apr 08, 2019 1:47 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Y’all would post my truck on that thread if y’all saw it lol small lift, big tires, and a big lab head sticker on the back lol
|
Mon Apr 08, 2019 4:49 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Mon Apr 08, 2019 9:37 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Them tacos are like J B Weld, they never break lol
|
Tue Apr 09, 2019 6:30 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ Refurbishing a Prodrive
|
Tue Apr 09, 2019 6:52 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Taco’s way under powered and doesn’t tow worth a damn. For what it is tho it’s a durable little truck just wouldn’t recommend it for the real serious redneckin’ [FACE WITH TEARS OF JOY]
Sent from my iPhone using Tapatalk
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Tue Apr 09, 2019 7:48 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Yeah, my boy has a new tundra with a 6 inch lift that is just straight nasty. Tundras look great jacked up, but he also complains about the gas mileage a lot
|
Tue Apr 09, 2019 7:54 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am Posts: 4323 Location: Cut Off, La.
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ Refurbishing a Prodrive
|
Tue Apr 09, 2019 8:36 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Buzz Killington
MMT 1000 Club
Joined: Tue Jan 10, 2012 12:33 pm Posts: 2455
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Looks great man. Sucks I didn't get to see it in person. Next time....
Support your troops. We support you.
B.
_________________ Support your troops - they support you
B. MacDonald
|
Tue Apr 09, 2019 1:28 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
dhall
MMT Pro Member
Joined: Wed Jan 30, 2013 3:42 pm Posts: 53
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Have you had more than 2 people in it yet I am looking at a go devil 20x60 with the 40 fnr and want to know if it will plane with 4 people.
|
Mon Apr 15, 2019 2:05 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Russ
MMT 1000 Club
Joined: Mon Dec 31, 2012 11:07 pm Posts: 4820 Location: West Monroe, LA
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Yes it will.
#CFFITR #GhostBoat #Whoneedsphysicsihaveamudmotor
|
Mon Apr 15, 2019 2:22 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Absolutely it will
|
Mon Apr 15, 2019 7:58 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
dead animal
MMT 1000 Club
Joined: Fri Jan 16, 2009 3:18 pm Posts: 1726
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
you tried moving the motor over a inch or so to kill that tiller torque? might help, ask ur boat builder.
nice rig!!!
|
Tue Apr 16, 2019 8:28 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Wed Apr 17, 2019 9:20 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Wed Apr 17, 2019 9:32 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
It sounds really nice man. I found my tiller torque got better over time once I got used to the rig. I also found that getting my props balanced helped a little too
|
Thu Apr 18, 2019 6:05 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
Good stuff ya’ll thanks I’m digging the boat.. one of these days I’ll be back in Tejas and I’ll def rip this beast out to Caddo or some of the other rides!
Last weekend I re-centered the motor and replaced the plastic throttle control with a lever control throttle. I’m gonna try and refrain from doing much else til warranty expires. It come with GD 11x12 3 blade. You’d think in stock form that’s the best play but Ill look into it when this one wears.
Another plus with new GD FNR is hex shaft so that opens up more prop options than ever before for GD’s
Sent from my iPhone using Tapatalk
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Thu Apr 18, 2019 6:53 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
I like that FNR a lot. That’s what I would have purchased if it would have had hydraulic trim
|
Thu Apr 18, 2019 10:28 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Will
MMT Elite Member
Joined: Fri Jul 08, 2011 1:54 pm Posts: 8133
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
How's the skeg on that GD? Can you bend the torque tab or add one?
_________________ Before the internet, the majority of the village idiots stayed in their villages.
|
Thu Apr 18, 2019 11:06 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Gigafowl
MMT Elite Member
Joined: Tue Jan 13, 2009 7:19 pm Posts: 6441 Location: Trinity Bay - Texas
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ Eat - Sleep - Hunt ! ! !
"It is good to have an end to journey toward; but it is the journey that matters, in the end."
|
Thu Apr 18, 2019 8:48 pm |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
kirk
MMT F.E.
Joined: Thu Apr 18, 2013 5:52 pm Posts: 870 Location: SW LA
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
|
Sat Apr 20, 2019 9:15 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Tue Apr 30, 2019 6:58 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Wchauvin
MMT 1000 Club
Joined: Sat Sep 30, 2017 7:10 pm Posts: 1872
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
I’m thinking about switching to the bps one as well
|
Tue Apr 30, 2019 6:59 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
Anthonyaarnold
MMT Pro Member
Joined: Thu May 14, 2015 7:43 am Posts: 174 Location: SLC, UT/ARK-LA-TEX bred
|
![Post Post](./styles/acidtech_tiger/imageset/icon_topic_latest.gif) Re: 20x50 WC Custom // Go Devil 40 FNR Review
You do not have the required permissions to view the files attached to this post.
_________________ 40 Go Devil FNR on 20x48 WC Custom --
|
Tue Apr 30, 2019 7:07 am |
|
![](./styles/acidtech_tiger/theme/images/spacer.gif) |
|