ProDrive rib nuts..... is that kinda like Gatortail Chin Nuts?????
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Prodrive rib nuts https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=1806 |
Page 1 of 1 |
| Author: | PaulDarensbourg [ Tue Apr 28, 2009 12:04 pm ] |
| Post subject: | Prodrive rib nuts |
Anyone know where I can get some of those rib nuts that prodrive puts in there cross bracing for the seat to bolt in? Also, what is the correct name for them? |
|
| Author: | SwampSnyper [ Tue Apr 28, 2009 12:20 pm ] |
| Post subject: | Re: Prodrive rib nuts |
http://www.fastenermart.com/html/600220000040.html |
|
| Author: | Mudgun [ Tue Apr 28, 2009 12:37 pm ] |
| Post subject: | Re: Prodrive rib nuts |
riv-nut or nutsert fastenal.com |
|
| Author: | PaulDarensbourg [ Tue Apr 28, 2009 12:44 pm ] |
| Post subject: | Re: Prodrive rib nuts |
thanks, another retarded question, but about what size do they use? Now that I have found them I have also found out that there is a huge selection of them to pick from. |
|
| Author: | Rail [ Tue Apr 28, 2009 1:40 pm ] |
| Post subject: | Re: Prodrive rib nuts |
Shank length plays into the mix also.. You need to know how think the material is that your putting them in.. The PD riv-nuts are either 1/4x20 or 5/16x18 if I remember right.. |
|
| Author: | mudd [ Tue Apr 28, 2009 1:46 pm ] |
| Post subject: | Re: Prodrive rib nuts |
You can get them at Menards along with the tool in the same isle as the rivits |
|
| Author: | Crews [ Tue Apr 28, 2009 1:55 pm ] |
| Post subject: | Re: Prodrive rib nuts |
ProDrive rib nuts..... is that kinda like Gatortail Chin Nuts?????
|
|
| Author: | PaulDarensbourg [ Tue Apr 28, 2009 2:17 pm ] |
| Post subject: | Re: Prodrive rib nuts |
| Author: | deltaduckmaster [ Tue Apr 28, 2009 4:49 pm ] |
| Post subject: | Re: Prodrive rib nuts |
| Author: | benelliman [ Tue Apr 28, 2009 5:19 pm ] |
| Post subject: | Re: Prodrive rib nuts |
Paul you can get them from godevil with the tool. |
|
| Author: | LOWRY [ Tue Apr 28, 2009 5:33 pm ] |
| Post subject: | Re: Prodrive rib nuts |
You can find the "kits" on ebay. Contains the tool and several sizes of the fasteners. Guy at the fastener store here in Tyler showed me how to set them without a tool. It can be done but the tool makes it a whole lot easier. |
|
| Author: | duckfire [ Wed Apr 29, 2009 12:55 am ] |
| Post subject: | Re: Prodrive rib nuts |
When I bought my Quickset blind it came with some rivnuts and a "tool" to set them. The tool was a 1/4 20 bolt and a nut. Thread the nut on the bolt, then the rivnut. |
|
| Author: | Jim1648 [ Sat May 02, 2009 4:33 pm ] |
| Post subject: | Re: Prodrive rib nuts |
http://www.rivetnuttool.com/ |
|
| Author: | RC [ Wed May 06, 2009 7:00 am ] |
| Post subject: | Re: Prodrive rib nuts |
All the PD boats I had, were 3/8x16 riv nuts. Cardinal tool has a fairly cheap tool for installing them, mine cost $65 a couple years ago. You can get the riv-nuts at Tool: (bottom one!) Bought plain stainless allen head bolts and the black "wing-nut" caps that snap over the bolts at the local true value hardware. |
|
| Author: | balloon-knot [ Wed May 06, 2009 2:27 pm ] |
| Post subject: | Re: Prodrive rib nuts |
I got a kit at Home Depot. It would not install the 3/8 Riv nuts but had 3 smaller attachments. $19 if I remember right. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|