I think its the boat. Should've got a 18x48
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| what speeds should i be gettin https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=18899 |
Page 1 of 1 |
| Author: | duckmananderson [ Sun May 29, 2011 12:59 pm ] |
| Post subject: | what speeds should i be gettin |
i got a 1754 gator tail boat witha 35 hp mud buddy motor is stock . just wounderin what i should be gettin went out fishin today me the wife and my dad so just fishin gear not major weight and got 21.3mph |
|
| Author: | dfou [ Sun May 29, 2011 1:05 pm ] |
| Post subject: | what speeds should i be gettin |
Well I got a 1650 and with 2 guys (230&210) plus icechest full of beer and anchor etc ran 26.5 consistent and 27.4 at it's fastest |
|
| Author: | Timbeaux [ Sun May 29, 2011 3:27 pm ] |
| Post subject: | Re: what speeds should i be gettin |
I'm running a 17 x 50 flat with a GTR35. With 2 guys 165, 230, ice chest and fishing gear I run 26-27, and can hit 28 by myself. Whats you rpms? |
|
| Author: | duckmananderson [ Sun May 29, 2011 3:46 pm ] |
| Post subject: | Re: what speeds should i be gettin |
rpm are 3800 to 3900 ish |
|
| Author: | Timbeaux [ Sun May 29, 2011 3:49 pm ] |
| Post subject: | Re: what speeds should i be gettin |
Thats what I'm turning |
|
| Author: | duckmananderson [ Sun May 29, 2011 4:45 pm ] |
| Post subject: | Re: what speeds should i be gettin |
any ides what it could be ? |
|
| Author: | slambin [ Sun May 29, 2011 6:38 pm ] |
| Post subject: | Re: what speeds should i be gettin |
| Author: | duckmananderson [ Sun May 29, 2011 6:46 pm ] |
| Post subject: | Re: what speeds should i be gettin |
thats what i was thinkin anyone got a pic on how to measure the prop ? thanks |
|
| Author: | med [ Sun May 29, 2011 8:00 pm ] |
| Post subject: | Re: what speeds should i be gettin |
Have any bad hooks? |
|
| Author: | duckmananderson [ Sun May 29, 2011 8:37 pm ] |
| Post subject: | Re: what speeds should i be gettin |
No hooks at all |
|
| Author: | waggman [ Sun May 29, 2011 11:52 pm ] |
| Post subject: | Re: what speeds should i be gettin |
I think its the boat. Should've got a 18x48
|
|
| Author: | duckmananderson [ Mon May 30, 2011 2:35 pm ] |
| Post subject: | Re: what speeds should i be gettin |
i dont think its the boat |
|
| Author: | swamprat11 [ Wed Jun 01, 2011 11:54 am ] |
| Post subject: | Re: what speeds should i be gettin |
size matters as does weight that does seem a little slow, move your weight around and work with the trim, there is a sweet spot and you will know when you find it. also, your hull isnt cupped is it, that will KILL your speed |
|
| Author: | duckmananderson [ Wed Jun 01, 2011 3:25 pm ] |
| Post subject: | Re: what speeds should i be gettin |
ok what does cupped mean ? lol never heard that one yet |
|
| Author: | Woodiebuster [ Wed Jun 01, 2011 3:40 pm ] |
| Post subject: | Re: what speeds should i be gettin |
i think he means hooked |
|
| Author: | swamprat11 [ Thu Jun 02, 2011 6:50 am ] |
| Post subject: | Re: what speeds should i be gettin |
hooked is a new one to me, but probably means the same. run over too many logs and the center of the boat is pushed up. this makes it suck to the water and holds your speep down, doeswnt matter much when takin off, but kills you on top-end. BIG PROBLEM in SC and sometimes hard to see. a long straight edge will tell u though. check and see |
|
| Author: | scduxman [ Mon Jun 06, 2011 4:12 pm ] |
| Post subject: | Re: what speeds should i be gettin |
Just got a 1644 gator trax with a 4500 black death MB. What kinda speeds should I see. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|