Instead of being a dik, just measure it for him or STFU Bitchski. Its not becoming of you. Dude ain't trying to get into a pissing contest with you and you still not at FE status yet.
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Rivets https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=3163 |
Page 1 of 1 |
| Author: | Shooter007 [ Mon Jul 13, 2009 2:50 pm ] |
| Post subject: | Rivets |
Quick question can someone tell me what the spacing on the rivets on their floor is at? Specifically anyone with a phowler or TMT. I'm finishing my floor and just want to get it right. I believe it is 6 inches apart on the runners. Thanks. |
|
| Author: | Mitschke [ Mon Jul 13, 2009 3:40 pm ] |
| Post subject: | Re: Rivets |
Thats alot of rivets... Im think every 12" is doable. |
|
| Author: | Shooter007 [ Mon Jul 13, 2009 4:18 pm ] |
| Post subject: | Re: Rivets |
I agree, I guess I figured I would rather have more then less. Based on what I have in the three main panels that would work out to 30 per panel. There are 5 runner and I've set them 1" off the edge of each panel then every six inches after that, the math seemed to work out best with that. I was just looking for what the manufacturer standard was? Since we aren't talking any real weight difference it's just the install that will take a bit longer. Anyone else have a boat they could take a look at? Thanks |
|
| Author: | Mitschke [ Mon Jul 13, 2009 4:48 pm ] |
| Post subject: | Re: Rivets |
Yah sure. Every 12 inches. I have an Aucoin boat. So do 200 other people here on the site. Lets see. I have 11' of planing surface, plus a foot of rake untill my floor dead ends at my gas tank. That is 12' I have 6 runners. 6 times 12 equals 72. There you have it. |
|
| Author: | POKER1 [ Mon Jul 13, 2009 5:42 pm ] |
| Post subject: | Re: Rivets |
Instead of being a dik, just measure it for him or STFU Bitchski. Its not becoming of you. Dude ain't trying to get into a pissing contest with you and you still not at FE status yet.
|
|
| Author: | Mitschke [ Mon Jul 13, 2009 6:16 pm ] |
| Post subject: | Re: Rivets |
| Author: | Shooter007 [ Mon Jul 13, 2009 7:56 pm ] |
| Post subject: | Re: Rivets |
No offense taken, didn't even take it that way Thanks for taking the time to measure. |
|
| Author: | coondik [ Mon Jul 13, 2009 8:01 pm ] |
| Post subject: | Re: Rivets |
mitsi, u'r sincerity and grattitude are absolutely rivet-ting |
|
| Author: | Shooter007 [ Mon Jul 13, 2009 8:14 pm ] |
| Post subject: | Re: Rivets |
 What can say I was trying to start the week on a good note, god knows there is plenty of time for it to go to shxt.
|
|
| Author: | quackconsumer [ Mon Jul 13, 2009 8:41 pm ] |
| Post subject: | Re: Rivets |
Why not just screw it down wit stainless self-tapping screws? |
|
| Author: | Mudgun [ Tue Jul 14, 2009 5:53 am ] |
| Post subject: | Re: Rivets |
I would say stick with rivets and here's why: Eventually the srews will back out from vibration. When you put a self-tapper back in there, it won't seat as tightly as the previous one unless you step up in size. With rivets, they won't back out. If you shear the head off, you can go right back with the same sized rivet in the existing hole. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|