I use a bungee cord from back handle to back handle and it holds mine
down just fine.
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Trailering PD motors https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=2&t=552 |
Page 1 of 1 |
| Author: | Full Throttle [ Mon Feb 09, 2009 8:52 pm ] |
| Post subject: | Trailering PD motors |
How do yall trailer your motors?? I'ven just been trimming it up against the reverse block and tying the handle off to one side. If I recall, KP said that's the way to do it, but am second guessing that now. Is that right or is there a better way? |
|
| Author: | cash [ Mon Feb 09, 2009 9:35 pm ] |
| Post subject: | Re: Trailering PD motors |
I do the same. Not sure if its the right or wrong way but thats what I do. |
|
| Author: | Crews [ Mon Feb 09, 2009 10:27 pm ] |
| Post subject: | Re: Trailering PD motors |
that's what I do. no need to overthink. unless you have a boat with a transom not designed for a ProDrive. |
|
| Author: | Swamp Wader [ Tue Feb 10, 2009 6:54 am ] |
| Post subject: | Re: Trailering PD motors |
I think trailering mine like that wore the bushings out in mine.. I now roll like this.. No bouncing or twisting on the transom anymore. That hose on the cav plate is a piece of low pressure Hydro hose I had laying around http://rebeloffroad.net/Gallery/albums/ ... .sized.jpg |
|
| Author: | Full Throttle [ Tue Feb 10, 2009 7:05 am ] |
| Post subject: | Re: Trailering PD motors |
| Author: | coastal [ Tue Feb 10, 2009 10:01 am ] |
| Post subject: | Re: Trailering PD motors |
Anything is better than your motor bouncing up and down beating the sheet out of everything. |
|
| Author: | hotdognjo [ Tue Feb 10, 2009 10:04 am ] |
| Post subject: | Re: Trailering PD motors |
I use a bungee cord from back handle to back handle and it holds mine down just fine.
|
|
| Author: | Pappy Gander [ Tue Feb 10, 2009 11:12 am ] |
| Post subject: | Re: Trailering PD motors |
I got me a boat not made for a heavy PD so I went with an adjustable angled transom saver from Cabelas. That along wit a strap does the trick. |
|
| Author: | Allterrain [ Tue Feb 10, 2009 11:23 am ] |
| Post subject: | Re: Trailering PD motors |
This is how i used to trailer my PD before i sold it. http://i107.photobucket.com/albums/m288 ... jr/TrA.jpg |
|
| Author: | D Duck [ Tue Feb 10, 2009 3:46 pm ] |
| Post subject: | Re: Trailering PD motors |
| Author: | Full Throttle [ Tue Feb 10, 2009 5:21 pm ] |
| Post subject: | Re: Trailering PD motors |
| Author: | dylndaw [ Tue Feb 10, 2009 8:56 pm ] |
| Post subject: | Re: Trailering PD motors |
you have to buy the transome-saver and cut it to lenth and at an angle to accomadate your motor. I drilled my fin to hold all in place. looks like the same thing i did D DUCK |
|
| Author: | blaze [ Tue Feb 10, 2009 9:43 pm ] |
| Post subject: | Re: Trailering PD motors |
JP had a good idea and its the same thing I did with mine. Some stainless tubing and unistrut |
|
| Author: | POKER1 [ Tue Feb 10, 2009 10:53 pm ] |
| Post subject: | Re: Trailering PD motors |
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|
