| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Height of console https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=4&t=68232 |
Page 1 of 1 |
| Author: | North LA Hunter [ Tue Sep 13, 2016 6:41 am ] |
| Post subject: | Height of console |
Need some help from those who have center consoles. Like a dummy I didn't write down my measurements off of my other console and now I have to figure it out again. I cut one out that was 32" tall and it seems too short. It would be perfect if I sat down while driving but I stand up most of the time. And besides it looks stupid in my boat. Could a few of you tell me how tall your consoles are to the top and if you would change anything about the angle or height? Thanks in advance!! Sent from my beeper |
|
| Author: | TPerkins [ Tue Sep 13, 2016 6:47 am ] |
| Post subject: | Re: Height of console |
I'll measure mine when I get home. I feel mine is more comfortable to run sitting but I'm 6'1". It's OK to run standing but just not as comfortable. 3CK's willet rig to me is perfect to run standing. Sent from my SM-G920V using Tapatalk |
|
| Author: | North LA Hunter [ Tue Sep 13, 2016 7:00 am ] |
| Post subject: | Re: Height of console |
Ten fo. I wish I could get a hold of the guy that I sold it to and get him to measure mine. Here's a picture of it. Sent from my beeper |
|
| Author: | OwenDickeson [ Tue Sep 13, 2016 7:49 am ] |
| Post subject: | Re: Height of console |
Mine measures 30" at the bend and is a good height for standing operation. Pro-Drive's measure 24" and are best for seated operation. Sent from my XT1254 using Tapatalk |
|
| Author: | 3rd Coast Killer [ Tue Sep 13, 2016 8:03 am ] |
| Post subject: | Re: Height of console |
| Author: | North LA Hunter [ Tue Sep 13, 2016 8:06 am ] |
| Post subject: | Re: Height of console |
The one I cut out measures 25" to that point Owen. I like the design but it looks awfully short to me. The one I measured off of was 24" and like you say it's perfect for sitting. Sent from my beeper |
|
| Author: | b.latiolais [ Tue Sep 13, 2016 8:39 am ] |
| Post subject: | Re: Height of console |
| Author: | North LA Hunter [ Tue Sep 13, 2016 8:44 am ] |
| Post subject: | Re: Height of console |
Haha! I doubt I build it but I'm goin to keep it in case someone needs one! I haven't got all of it cut out though. Sent from my beeper |
|
| Author: | b.latiolais [ Tue Sep 13, 2016 8:46 am ] |
| Post subject: | Re: Height of console |
Just messing with ya. Sometimes I wish I had a console but I really like the open layout. |
|
| Author: | Will [ Tue Sep 13, 2016 9:08 am ] |
| Post subject: | Re: Height of console |
FWIW a standard counter top height is 36", looking at your design, if the top tray was at 36", where would that put the lowest point, around 30" ? Seems like it would be perfect to me... |
|
| Author: | Frog [ Tue Sep 13, 2016 9:21 am ] |
| Post subject: | Re: Height of console |
I like my short console for sitting and concealing but it sucks for standing I believe its 28" high but will measure it. |
|
| Author: | North LA Hunter [ Tue Sep 13, 2016 9:25 am ] |
| Post subject: | Re: Height of console |
| Author: | Will [ Tue Sep 13, 2016 9:27 am ] |
| Post subject: | Re: Height of console |
easier to reach up while sitting then slumped over while standing. |
|
| Author: | Hernaja1 [ Tue Sep 13, 2016 10:13 am ] |
| Post subject: | Re: Height of console |
I can measure mine but mines a little wider then most lol. I'm 5,9 and is perfect for me standing up or in my cases leaning against my leaning post. Even sitting on it is pretty comfortable. |
|
| Author: | North LA Hunter [ Tue Sep 13, 2016 10:45 am ] |
| Post subject: | Re: Height of console |
| Author: | rob_E [ Tue Sep 13, 2016 10:57 am ] |
| Post subject: | Re: Height of console |
I based mine off your other console design.... I went with a 9" deep glove box and overall height of 45". Mine is 1" shorter than the motor trimmed all the way down in the middle hole. |
|
| Author: | Bigbend [ Tue Sep 13, 2016 12:19 pm ] |
| Post subject: | Re: Height of console |
Those glove boxes are awesome on top of those. Might be cool to add an insert for holding beer too. |
|
| Author: | North LA Hunter [ Tue Sep 13, 2016 12:46 pm ] |
| Post subject: | Re: Height of console |
| Author: | kirk [ Tue Sep 13, 2016 1:03 pm ] |
| Post subject: | Re: Height of console |
| Author: | rob_E [ Tue Sep 13, 2016 5:27 pm ] |
| Post subject: | Re: Height of console |
| Author: | OwenDickeson [ Wed Sep 14, 2016 7:44 am ] |
| Post subject: | Re: Height of console |
| Author: | TPerkins [ Wed Sep 14, 2016 4:59 pm ] |
| Post subject: | Re: Height of console |
Sent from my SM-G920V using Tapatalk |
|
| Author: | North LA Hunter [ Thu Sep 15, 2016 4:53 am ] |
| Post subject: | Re: Height of console |
That what mine ended being Tad. Thinking about making it 28"-30" to the bottom and 38"-40" to the top. Thanks for the help!!! Sent from my beeper |
|
| Author: | TPerkins [ Thu Sep 15, 2016 6:53 am ] |
| Post subject: | Re: Height of console |
Those measurement would be perfect Sent from my SM-G920V using Tapatalk |
|
| Author: | willett [ Tue Sep 20, 2016 8:51 pm ] |
| Post subject: | Re: Height of console |
All of mine are 38" tall unless someone specifies differently Sent from my iPhone using Tapatalk |
|
| Author: | kirk [ Wed Sep 21, 2016 12:55 pm ] |
| Post subject: | Re: Height of console |
| Author: | North LA Hunter [ Fri Sep 23, 2016 7:39 am ] |
| Post subject: | Re: Height of console |
The top of a tall transom GTR is about 52" above the floor. Sent from my beeper |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|