| Author |
Message |
|
baileydog
MMT Member
Joined: Fri Feb 20, 2009 7:08 am
Posts: 11
|
 Broke off Hand wheel on a PD 36 Got to the ramp yesterday and well. I saw the motor was hanging LOW.
The screw the hand wheel is on is now broken.
It broke off in the hand wheel.
I want to hunt 12/26.
Any ideas?
I put a rope around the vertical handle and tied the motor up enough to run 5 mins each way to hunt yesterday.
I am going to Homedepot today.
Looking at getting a bolt and nut.
_________________
No good deed goes unpunished
|
| Tue Dec 24, 2013 8:11 am |
|
|
|
JLACOUR
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:18 pm
Posts: 4915
Location: Lake Jackson, TX
|
Re: Broke off Hand wheel on a PD 36 Where r u located? I have one
_________________
37 PD EFI FPR 18x48 Tiller
SOLD -- 36 PD EFI FPR 18x48 Stick Steer
SOLD -- 27 PD FPR 16x36 Skiff
|
| Tue Dec 24, 2013 8:17 am |
|
|
|
JIMMY W
MMT 1000 Club
Joined: Tue Jan 13, 2009 8:02 pm
Posts: 4534
Location: South Louisiana
|
Re: Broke off Hand wheel on a PD 36 Damn and yall was making fun of mudbuddys falling off! 
_________________
17/54 GT EXTREME Center Console, Huntdeck w/ GTR 35
Hoyt Mods and some other goodies
|
| Tue Dec 24, 2013 9:24 am |
|
|
|
baileydog
MMT Member
Joined: Fri Feb 20, 2009 7:08 am
Posts: 11
|
Re: Broke off Hand wheel on a PD 36 Alabama.
I think I need the worm shaft and the wheel.
Thanks.
_________________
No good deed goes unpunished
|
| Tue Dec 24, 2013 10:18 am |
|
|
|
JLACOUR
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:18 pm
Posts: 4915
Location: Lake Jackson, TX
|
Re: Broke off Hand wheel on a PD 36 You can have mine but you wouldn't get it by the 26th. Pm me if you want it.
_________________
37 PD EFI FPR 18x48 Tiller
SOLD -- 36 PD EFI FPR 18x48 Stick Steer
SOLD -- 27 PD FPR 16x36 Skiff
|
| Tue Dec 24, 2013 10:43 am |
|
|
|
naj
MMT 1000 Club
Joined: Fri Jan 22, 2010 8:40 pm
Posts: 1620
Location: Larose, Louisiana
|
Re: Broke off Hand wheel on a PD 36
_________________
18' X 48" Center Console Sportsman Fab with a Yamaha F70LA
18' X 48" Center Console Sportsman Fab Dragging a 36hp ProDrive
15' X 42" Sea Arch with a 27hp ProDrive
|
| Tue Dec 24, 2013 10:48 am |
|
|
|
SCSuperfly
MMT Pro Member
Joined: Fri Nov 25, 2011 1:24 am
Posts: 466
|
Re: Broke off Hand wheel on a PD 36 Mine broke a while back too . I lucked out and found a piece of acme thread that matched and just replaced it. It's 5/8 by something, can't remember. Common size though.
_________________
Modded 36 PD draggin' around an 1848 PD boat backwards!
|
| Fri Dec 27, 2013 12:58 pm |
|
|
|
Will
MMT Elite Member
Joined: Fri Jul 08, 2011 1:54 pm
Posts: 8133
|
Re: Broke off Hand wheel on a PD 36 Wouldn't happen to be the same as a C-clamp would it?
_________________
Before the internet, the majority of the village idiots stayed in their villages.
|
| Fri Dec 27, 2013 1:08 pm |
|
|
|
duckduckboom
MMT Elite Member
Joined: Tue Nov 23, 2010 6:33 pm
Posts: 5603
Location: Corner of Hell an high water, La
|
Re: Broke off Hand wheel on a PD 36 Winch trim it
_________________
You have your whole life to be an idiot, take a day off!
|
| Fri Dec 27, 2013 4:21 pm |
|
|
|
SCSuperfly
MMT Pro Member
Joined: Fri Nov 25, 2011 1:24 am
Posts: 466
|
Re: Broke off Hand wheel on a PD 36 Believe it or not, I did check a few c clamps. Ha!
_________________
Modded 36 PD draggin' around an 1848 PD boat backwards!
|
| Mon Dec 30, 2013 11:34 am |
|
|
|
ROGER504
MMT Pro Member
Joined: Sat Sep 18, 2010 11:20 am
Posts: 52
Location: METAIRIE, LA
|
Re: Broke off Hand wheel on a PD 36 If you didn't get one from JLACOUR, I have one that came off a PD 27 I m not sure if they are the same tho.
_________________
1648 GDSD WITH 36PD
|
| Mon Dec 30, 2013 4:13 pm |
|
|
|
JLACOUR
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:18 pm
Posts: 4915
Location: Lake Jackson, TX
|
Re: Broke off Hand wheel on a PD 36 He didn't get mine yet. I've been out of town and I'm waiting for him to confirm that he wants it for the cost of shipping. He is in Arkansas.
_________________
37 PD EFI FPR 18x48 Tiller
SOLD -- 36 PD EFI FPR 18x48 Stick Steer
SOLD -- 27 PD FPR 16x36 Skiff
|
| Mon Dec 30, 2013 4:18 pm |
|
|
|
