| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| 11x10 prop for 23hp https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=27271 |
Page 1 of 1 |
| Author: | duckman223 [ Thu Mar 01, 2012 11:30 am ] |
| Post subject: | 11x10 prop for 23hp |
I have a 14hp mudbuddy mini sufacedrive.I got a 23hp vanguard to fit on the frame. Just not sure what prop to buy. |
|
| Author: | CCC [ Thu Mar 01, 2012 11:42 am ] |
| Post subject: | 9x6 or 9x5 prop for 23hp |
My 23 has a 11x10 |
|
| Author: | duckman223 [ Thu Mar 01, 2012 11:47 am ] |
| Post subject: | Re: 9x6 or 9x5 prop for 23hp |
Well on the mudbuddy site it has a 9x5 or 9x6 fitting a 23hp vanguard. |
|
| Author: | CCC [ Thu Mar 01, 2012 11:50 am ] |
| Post subject: | 9x6 or 9x5 prop for 23hp |
They might be geared diff idk |
|
| Author: | CCC [ Thu Mar 01, 2012 11:53 am ] |
| Post subject: | 9x6 or 9x5 prop for 23hp |
That's long tail props the site has 11x10 for 21-29 hp motors |
|
| Author: | duckman223 [ Thu Mar 01, 2012 12:01 pm ] |
| Post subject: | Re: 9x6 or 9x5 prop for 23hp |
Oh okay i just dont wana buy the wrong prop.I hope a prop would work with that 23 on that frame a guy told me a regeared diff. |
|
| Author: | Mag10 [ Thu Mar 01, 2012 12:25 pm ] |
| Post subject: | Re: 11x10 prop for 23hp |
Check your current prop it is probably threaded. Most of the 11X10s will be hex. |
|
| Author: | duckman223 [ Thu Mar 01, 2012 1:00 pm ] |
| Post subject: | Re: 11x10 prop for 23hp |
It is threaded i looked online and i found a 11x10 prop 3/4 threaded. |
|
| Author: | bobbyjober [ Thu Mar 01, 2012 1:19 pm ] |
| Post subject: | Re: 11x10 prop for 23hp |
I did a swap from 18hp to a 24 Honda on a mini frame. I can run and do run a 12x12 GoDevil SD prop, that I had machined for 3/4-10 threaded. The gearing is lower than a 23 mini. Best bet is to try the 11x10 and see if you like the perormance, if not go from there. Hill Marine will make a 12x10, 12x11,and 12x12 in a 3/4-10 thread for an extra $50. |
|
| Author: | duckman223 [ Thu Mar 01, 2012 1:56 pm ] |
| Post subject: | Re: 11x10 prop for 23hp |
Yea thanks for the info i saw the 11x10 3/4 thread on hill marine also. |
|
| Author: | duckman223 [ Thu Mar 01, 2012 1:58 pm ] |
| Post subject: | Re: 11x10 prop for 23hp |
How fast do you get out of your boat and how fast ya think. My boat will go i have a 14ft alumcraft weights about 135 with a 23hp mini. |
|
| Author: | bobbyjober [ Fri Mar 02, 2012 8:45 am ] |
| Post subject: | Re: 11x10 prop for 23hp |
My setup runs 24mph, gets on plane with a load . My old ass boat is beat to crap also, when I run against wind and current, boat pops up and feels like I gain 5 more mph. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|