That hole in the water that you throw money in musta been hungry
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Never Ends https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=39348 |
Page 1 of 2 |
| Author: | Kmoppert [ Tue Apr 02, 2013 6:22 pm ] |
| Post subject: | Never Ends |
It's always something. What the F()ck! Heard grinding while busting through some lillies, look down and this is what I see. ImageUploadedByTapatalk1364948556.982313.jpg |
|
| Author: | cupped up [ Tue Apr 02, 2013 6:24 pm ] |
| Post subject: | Re: Never Ends |
That hole in the water that you throw money in musta been hungry
|
|
| Author: | instagator911 [ Tue Apr 02, 2013 6:27 pm ] |
| Post subject: | Re: Never Ends |
ouch! |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 6:28 pm ] |
| Post subject: | Re: Never Ends |
Yeah... |
|
| Author: | SwampDuck91 [ Tue Apr 02, 2013 6:33 pm ] |
| Post subject: | Re: Never Ends |
What does the cut down cav plate do, is there a reason behind it, I've seen a couple motor that had this done |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 6:50 pm ] |
| Post subject: | Re: Never Ends |
The cav plate won't drag when trimmed deep in mud, it allows water and mud to fall back down on the prop to bite better and I cut the length down on the back side so I could trim the prop further under the boat in reverse. |
|
| Author: | craig [ Tue Apr 02, 2013 6:52 pm ] |
| Post subject: | Re: Never Ends |
Ouch. Is that due to a bearing failure or loose/broken bolts? |
|
| Author: | deltaduckmaster [ Tue Apr 02, 2013 6:56 pm ] |
| Post subject: | Re: Never Ends |
How many hours on that bad boy. Should be under warranty |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 6:56 pm ] |
| Post subject: | Re: Never Ends |
I think the bolts broke loose. They tighten from either inside the knuckle or inside the shaft tower. Can't tell. Being towed in now by a trusty... Um... GTR... |
|
| Author: | cupped up [ Tue Apr 02, 2013 7:00 pm ] |
| Post subject: | Re: Never Ends |
| Author: | The Shafer [ Tue Apr 02, 2013 7:00 pm ] |
| Post subject: | Re: Never Ends |
| Author: | brasso [ Tue Apr 02, 2013 7:00 pm ] |
| Post subject: | Re: Never Ends |
| Author: | craig [ Tue Apr 02, 2013 7:00 pm ] |
| Post subject: | Re: Never Ends |
| Author: | OwenDickeson [ Tue Apr 02, 2013 7:10 pm ] |
| Post subject: | Re: Never Ends |
Damn.... No bueno |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 7:11 pm ] |
| Post subject: | Re: Never Ends |
I live in St. Martinville. Was playing in Charlo Lake behind the Lafayette Airport. |
|
| Author: | craig [ Tue Apr 02, 2013 7:13 pm ] |
| Post subject: | Re: Never Ends |
Oh you're close to PD headquarters then. |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 7:16 pm ] |
| Post subject: | Re: Never Ends |
Yeah, that's a plus. I'll drop it off tomorrow. Always something though. |
|
| Author: | naj [ Tue Apr 02, 2013 7:22 pm ] |
| Post subject: | Re: Never Ends |
I had alot of shit break on mine but never there. |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 7:24 pm ] |
| Post subject: | Re: Never Ends |
I guess that makes me a pioneer. |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 7:25 pm ] |
| Post subject: | Re: Never Ends |
What upsets me is that PD took the LU apart last to replace a broken shaft back in November. I've never even considered tightening or looking at those bolts. Hell, I can't even get to them! |
|
| Author: | MALLARDSX2 [ Tue Apr 02, 2013 7:26 pm ] |
| Post subject: | Re: Never Ends |
BOAT: BREAK OUT ANOTHER THOUSAND..........lol |
|
| Author: | Quackhead62 [ Tue Apr 02, 2013 7:28 pm ] |
| Post subject: | Re: Never Ends |
Not good at al. On the upside I dropped my PD off last week to get some stuff fixed an they weren't backed up like they usually are they were done with mine in a few days |
|
| Author: | craig [ Tue Apr 02, 2013 8:08 pm ] |
| Post subject: | Re: Never Ends |
| Author: | CJB [ Tue Apr 02, 2013 8:11 pm ] |
| Post subject: | Re: Never Ends |
^X2, sounds like ol boy is rough on his shit |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 8:11 pm ] |
| Post subject: | Re: Never Ends |
| Author: | Kmoppert [ Tue Apr 02, 2013 8:12 pm ] |
| Post subject: | Re: Never Ends |
ImageUploadedByTapatalk1364955116.172738.jpgImageUploadedByTapatalk1364955126.365599.jpg |
|
| Author: | med [ Tue Apr 02, 2013 8:20 pm ] |
| Post subject: | Re: Never Ends |
After pd sees it post back what happened |
|
| Author: | cupped up [ Tue Apr 02, 2013 8:20 pm ] |
| Post subject: | Re: Never Ends |
I wonder if those are studs threaded into that knuckle or if they're bolts with nuts inside the knuckle? I could see stripping the threads out of the knuckle, it'd be hard to believe 4 nuts would back off inside the knuckle or break off in there. I don't know dick about a PD, I'm just trying to figure out how that could happen. |
|
| Author: | Kmoppert [ Tue Apr 02, 2013 8:53 pm ] |
| Post subject: | Re: Never Ends |
I have Stockholme Syndrome with my motor. |
|
| Author: | duckduckboom [ Tue Apr 02, 2013 9:02 pm ] |
| Post subject: | Re: Never Ends |
You gotta drop the lower unit to get to those bolts. Don't feel bad though I sheard shaft collar bolts. I was talking to peck face to face when I told him that and he said how the fuck did you do that? |
|
| Author: | naj [ Tue Apr 02, 2013 9:12 pm ] |
| Post subject: | Re: Never Ends |
| Author: | Kmoppert [ Wed Apr 03, 2013 5:22 am ] |
| Post subject: | Re: Never Ends |
| Author: | Quackhead62 [ Wed Apr 03, 2013 6:17 am ] |
| Post subject: | Re: Never Ends |
does cutting down your cav plate really help out a lot? Ive been kicking around cutting my down |
|
| Author: | pooldoo73 [ Wed Apr 03, 2013 7:19 am ] |
| Post subject: | Re: Never Ends |
Looks like those bolts were stripped out of there place. Must have taken a few years to break that part. |
|
| Author: | Kmoppert [ Wed Apr 03, 2013 7:48 am ] |
| Post subject: | Re: Never Ends |
| Author: | deltaduckmaster [ Wed Apr 03, 2013 8:13 am ] |
| Post subject: | Re: Never Ends |
| Author: | Quackhead62 [ Wed Apr 03, 2013 8:13 am ] |
| Post subject: | Re: Never Ends |
How much did u cut off |
|
| Author: | jerimiahw [ Wed Apr 03, 2013 8:26 am ] |
| Post subject: | Re: Never Ends |
Well at least prodrive has great customer service should get it back quickly Bryan waited at shop for me Saturday before Easter so I could pick up a clutch hell most wouldn't even answer the phone when there closed I gotta say customer service is excellent there |
|
| Author: | johnny rebel [ Wed Apr 03, 2013 8:44 am ] |
| Post subject: | Re: Never Ends |
| Author: | johnny rebel [ Wed Apr 03, 2013 8:44 am ] |
| Post subject: | Re: Never Ends |
| Page 1 of 2 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|