| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| what size grease fitting https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=39913 |
Page 1 of 1 |
| Author: | bigjohn33 [ Sun Apr 21, 2013 6:19 am ] |
| Post subject: | what size grease fitting |
I have a 07 mudbuddy 29 hp van guard and was going to get a grease gun and lube the lower unit...what size fitting? also, just reg marine grease. It is missing the cap on it soo I nedd one of those too. thanks fellas |
|
| Author: | CCC [ Sun Apr 21, 2013 7:55 am ] |
| Post subject: | Re: what size grease fitting |
Take a grease fitting off, take it to the parts house and get one the same size. I use marine grease |
|
| Author: | Buzz Killington [ Sun Apr 21, 2013 7:18 pm ] |
| Post subject: | Re: what size grease fitting |
Marine grease |
|
| Author: | Buzz Killington [ Sun Apr 21, 2013 7:18 pm ] |
| Post subject: | Re: what size grease fitting |
And x2 on the fitting Just remove it and bring it along to buy a replacement |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 7:44 am ] |
| Post subject: | Re: what size grease fitting |
It does not have the cap (missing) , the other part comes off? |
|
| Author: | CCC [ Mon Apr 22, 2013 9:44 am ] |
| Post subject: | Re: what size grease fitting |
What cap? Take a picture |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 2:38 pm ] |
| Post subject: | Re: what size grease fitting |
i guess i should say,i bought a grease gun but dont seem to have the right fittings..what size should i be using? |
|
| Author: | CCC [ Mon Apr 22, 2013 4:39 pm ] |
| Post subject: | Re: what size grease fitting |
I'm still not following, usually grease zerks are pretty universal. |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 6:36 pm ] |
| Post subject: | Re: what size grease fitting |
By cap I meant to say the hexagonal screw that I took out where you pump the grease in. I have it and the gun now , I bought some grease fittings that screw in where the screw was . I can't tell if its getting grease when I pump however |
|
| Author: | msm8281 [ Mon Apr 22, 2013 6:54 pm ] |
| Post subject: | Re: what size grease fitting |
Is grease coming out of the gun while not on the fitting? Just keep pumping. It was probably empty. |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 7:05 pm ] |
| Post subject: | Re: what size grease fitting |
That's the thing, its rreally not coming out when pumping, if I hold the guns trigger mechanism it very very slowly comes out a little. |
|
| Author: | msm8281 [ Mon Apr 22, 2013 7:07 pm ] |
| Post subject: | Re: what size grease fitting |
U have a big gun or one of those little baby ones from Wal-Mart? |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 7:28 pm ] |
| Post subject: | Re: what size grease fitting |
one of those little bass pro jobbers |
|
| Author: | msm8281 [ Mon Apr 22, 2013 7:39 pm ] |
| Post subject: | Re: what size grease fitting |
Thats your problem. I had the same thing happen to me. Throw that trash away and get the standatd size gun. If u look in those lil tubes there only about1/2 -3/4 full. Just a ripoff imo. |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 7:43 pm ] |
| Post subject: | Re: what size grease fitting |
how much one of them run? apreciate the help |
|
| Author: | msm8281 [ Mon Apr 22, 2013 7:45 pm ] |
| Post subject: | Re: what size grease fitting |
Less than 20 bucks |
|
| Author: | bigjohn33 [ Mon Apr 22, 2013 7:52 pm ] |
| Post subject: | Re: what size grease fitting |
Auto part place.? |
|
| Author: | msm8281 [ Mon Apr 22, 2013 7:58 pm ] |
| Post subject: | Re: what size grease fitting |
Yea Oreilys, Autozone |
|
| Author: | bigjohn33 [ Wed Apr 24, 2013 8:31 am ] |
| Post subject: | Re: what size grease fitting |
HOw much grease to add? |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|