Damn and yall was making fun of mudbuddys falling off!
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Broke off Hand wheel on a PD 36 https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=48574 |
Page 1 of 1 |
| Author: | baileydog [ Tue Dec 24, 2013 8:11 am ] |
| Post subject: | Broke off Hand wheel on a PD 36 |
Got to the ramp yesterday and well. I saw the motor was hanging LOW. The screw the hand wheel is on is now broken. It broke off in the hand wheel. I want to hunt 12/26. Any ideas? I put a rope around the vertical handle and tied the motor up enough to run 5 mins each way to hunt yesterday. I am going to Homedepot today. Looking at getting a bolt and nut. |
|
| Author: | JLACOUR [ Tue Dec 24, 2013 8:17 am ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Where r u located? I have one |
|
| Author: | JIMMY W [ Tue Dec 24, 2013 9:24 am ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Damn and yall was making fun of mudbuddys falling off!
|
|
| Author: | baileydog [ Tue Dec 24, 2013 10:18 am ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Alabama. I think I need the worm shaft and the wheel. Thanks. |
|
| Author: | JLACOUR [ Tue Dec 24, 2013 10:43 am ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
You can have mine but you wouldn't get it by the 26th. Pm me if you want it. |
|
| Author: | naj [ Tue Dec 24, 2013 10:48 am ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
| Author: | SCSuperfly [ Fri Dec 27, 2013 12:58 pm ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Mine broke a while back too . I lucked out and found a piece of acme thread that matched and just replaced it. It's 5/8 by something, can't remember. Common size though. |
|
| Author: | Will [ Fri Dec 27, 2013 1:08 pm ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Wouldn't happen to be the same as a C-clamp would it? |
|
| Author: | duckduckboom [ Fri Dec 27, 2013 4:21 pm ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Winch trim it |
|
| Author: | SCSuperfly [ Mon Dec 30, 2013 11:34 am ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
Believe it or not, I did check a few c clamps. Ha! |
|
| Author: | ROGER504 [ Mon Dec 30, 2013 4:13 pm ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
If you didn't get one from JLACOUR, I have one that came off a PD 27 I m not sure if they are the same tho. |
|
| Author: | JLACOUR [ Mon Dec 30, 2013 4:18 pm ] |
| Post subject: | Re: Broke off Hand wheel on a PD 36 |
He didn't get mine yet. I've been out of town and I'm waiting for him to confirm that he wants it for the cost of shipping. He is in Arkansas. |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|