No I haven't ramped up my rpms yet.
Leaving good enough alone for the minute
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Tiller torque 35 HD Sport https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=53345 |
Page 1 of 1 |
| Author: | Buzz Killington [ Mon May 19, 2014 5:04 am ] |
| Post subject: | Tiller torque 35 HD Sport |
Holy crap, good thing you can bend the rear tab I fought that motor every second for 32 miles yesterday. Apparently I have to bend the tab ot a bit more. My old 11x10 prop with this worked flawlessly. The new BB puts a lot more torque on the handle. At 3850rpm running 22.3 with 3 of us and a fishing load - I had the football against my hip just to manage the torque. Cool story bro? |
|
| Author: | dillakilla12 [ Mon May 19, 2014 7:53 am ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
I just went from an 11x10 to a big blade on my 23. I notice a difference to! Hit 20.7 with 3 guys and w loaded down beer coolers. I also noticed a difference in my rpms also. Sent from my SM-N900V using Tapatalk |
|
| Author: | Buzz Killington [ Mon May 19, 2014 6:48 pm ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
Thats amazing for a 23hp btw Cudos |
|
| Author: | dillakilla12 [ Mon May 19, 2014 7:08 pm ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
Did your rpms drop when u swapped up to the bb? Just curious. Mine sounded like I was tagging a rev limiter at 4200-4300 but before I could pull around 4700 with the 11x10. I did swap a coil when I swapped prop but according to MB it's the only coil they offer.. Sent from my SM-N900V using Tapatalk |
|
| Author: | dillakilla12 [ Mon May 19, 2014 7:12 pm ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
I do remember getting better speeds with 11x10 with close to the same load Sent from my SM-N900V using Tapatalk |
|
| Author: | Buzz Killington [ Tue May 20, 2014 4:28 am ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
I haven't tried that actually. .. My 11x10 is a load carrying prop but it has a few rock dents in it that require fixing. Calling the prop shop in town to inquire about pricing. If I recall, I would rev limit at 4000 rpms with the 11x10 Was running 3860 for best speeds with the BB and the load this last weekend. The 11x10 was solo running. |
|
| Author: | Buzz Killington [ Tue May 20, 2014 4:29 am ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
No I haven't ramped up my rpms yet. Leaving good enough alone for the minute
|
|
| Author: | dillakilla12 [ Tue May 20, 2014 6:03 am ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
I'm gonna throw my 11x10 back on and run it and report back. Sent from my SM-N900V using Tapatalk |
|
| Author: | Gros'bec [ Wed Jun 25, 2014 8:22 pm ] |
| Post subject: | Re: Tiller torque 35 HD Sport |
My stock 35 mudbuddy with a Big Blade prop had a lot of tiller torque when I first got it. I bent the tab on the skeg a little at a time till I got it where there was none. I bent it a total of 1 inch more than it came with from the factory. Made sure to bend it in the original crease |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|