| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| 35 stage 2 mod pully size https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=41&t=60166 |
Page 1 of 1 |
| Author: | chevy01 [ Mon Feb 16, 2015 2:54 pm ] |
| Post subject: | 35 stage 2 mod pully size |
what size pullys are people running with a mudbuddy 35 stage 2 mods mikuni, boat doctor heads and a pvt cam. i currently have the stock 37,48 just wondering if any one changes them i can turn a hammer 4,600 rpms and would i benefit me to change them |
|
| Author: | zborden25 [ Mon Feb 16, 2015 5:56 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
interested in this as well |
|
| Author: | 270Handiman [ Mon Feb 16, 2015 6:24 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
The only reason you change gearing is to manipulate your rpm's. 4600 with the hammer is about perfect. Is that with your average load in the boat? If so, I'd say you're good. With a BB, you're probably close to 4850-4900, which again is about perfect. This all assumes you don't have a CDI motor, limited at 4700. |
|
| Author: | chevy01 [ Mon Feb 16, 2015 7:03 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
yes i have the cdi motor i havnt tried it with a new bigblade yet im gonna test it out this week but i am pretty sure its gonna hit the rev limiter what all do i have to do to put the 5200 coils in and be safe (rods&pistons)? |
|
| Author: | chevy01 [ Mon Feb 16, 2015 7:03 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
yes i have the cdi motor i havnt tried it with a new bigblade yet im gonna test it out this week but i am pretty sure its gonna hit the rev limiter what all do i have to do to put the 5200 coils in and be safe (rods&pistons)? |
|
| Author: | OwenDickeson [ Tue Feb 17, 2015 7:52 am ] |
| Post subject: | Re: 35 stage 2 mod pully size |
I would leave it right where you have it. |
|
| Author: | SCmudder7071 [ Tue Feb 17, 2015 8:55 am ] |
| Post subject: | Re: 35 stage 2 mod pully size |
They don't make 5200 coils. |
|
| Author: | msm8281 [ Tue Feb 17, 2015 9:01 am ] |
| Post subject: | Re: 35 stage 2 mod pully size |
He probably means rev limiter. |
|
| Author: | SCmudder7071 [ Tue Feb 17, 2015 3:58 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
Says he has a cdi motor... |
|
| Author: | 270Handiman [ Tue Feb 17, 2015 4:05 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
If your turning the hammer 4600 on a motor limited at 4700, then you're good. Leave that prop on it and go. |
|
| Author: | chevy01 [ Tue Feb 17, 2015 5:05 pm ] |
| Post subject: | Re: 35 stage 2 mod pully size |
Ok thanks Sent from my iPhone using Tapatalk |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|