Thanks for all the help, Willett. I hope you get all of your stuff done. Just get after that transom first.
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| Cutting it close https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=49&t=10148 |
Page 1 of 1 |
| Author: | bullsprig [ Wed Jun 09, 2010 11:33 am ] |
| Post subject: | Cutting it close |
I now feel sympathy for anyone who is trying to get finishing touches on their rig by the weekend. Right now I have a boat with an incomplete transom in the shop, a motor sitting in the crate at a dealer, and a piece of 1 3/4 by 4 tubing somewhere between Ft. Worth and Tyler. The only thing I have ready for Caddo is my ice chest. |
|
| Author: | keestan31 [ Wed Jun 09, 2010 12:13 pm ] |
| Post subject: | Re: Cutting it close |
Hope you get everything ready...you are going to be cutting it real close. |
|
| Author: | Brinkleydog [ Wed Jun 09, 2010 1:02 pm ] |
| Post subject: | Re: Cutting it close |
Man if you need some tubing give me a call......if its Aluminume or Copper i got it in Gilmer. Ordered allt he stuff needed to make a poling platform and bow fishing deck and it was here in a week. later James 903-738-3316 |
|
| Author: | willett [ Wed Jun 09, 2010 1:04 pm ] |
| Post subject: | Re: Cutting it close |
didnt think bout that james but doubt you have that size tubing at you're shop not even places in tyler and shreveport that stock large qty of metal had it..... AO it's still on the ups truck but will be here today ive still got a lot to do to get ready including put a carb on the geny and its pouring down rain |
|
| Author: | bullsprig [ Wed Jun 09, 2010 1:06 pm ] |
| Post subject: | Re: Cutting it close |
Thank, James. Im about to check with Willet and find out if the tubing is here. But if it doesnt show up by this evening I may give you a call. |
|
| Author: | willett [ Wed Jun 09, 2010 1:13 pm ] |
| Post subject: | Re: Cutting it close |
hasnt made it to the door yet but trackin shows it on the truck so probably be here bout 4 |
|
| Author: | Brinkleydog [ Wed Jun 09, 2010 1:30 pm ] |
| Post subject: | Re: Cutting it close |
all i have instock righ now is 1" SCH 40 6061-T6 ALUM STRUC PIPE Willet will get you taken can of my friend...... |
|
| Author: | Joe M [ Wed Jun 09, 2010 3:05 pm ] |
| Post subject: | Re: Cutting it close |
Willet, I got a fine genny just sittin here if you need to borrow it 6250watt. |
|
| Author: | willett [ Wed Jun 09, 2010 3:08 pm ] |
| Post subject: | Re: Cutting it close |
lol thanks but meant the generac 32 hp motor thats on my boat right now |
|
| Author: | Joe M [ Wed Jun 09, 2010 3:17 pm ] |
| Post subject: | Re: Cutting it close |
Yea I figured that out a second ago. |
|
| Author: | willett [ Wed Jun 09, 2010 6:53 pm ] |
| Post subject: | Re: Cutting it close |
finally got the peice of metal in for bullsprigs boat, finished an online defensive driving course, got clothes washed and packed, coolers loaded up, and still havent gotten to put carb on the motor. Gotta get to marshall and finish bullsprigs transom in the AM, drop it off to get the motor hung, go to grocery store and fill up with gas before headin to lake....bout only thing want to do is get amp and speakers hooked up but doesnt look like that'll happen See yall tomorrow or sometime this weekend! |
|
| Author: | bullsprig [ Thu Jun 10, 2010 7:43 am ] |
| Post subject: | Re: Cutting it close |
Thanks for all the help, Willett. I hope you get all of your stuff done. Just get after that transom first.
|
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|