excellent review
| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| 17x48 X-series W/ 36 PD https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=5&t=14974 |
Page 1 of 1 |
| Author: | BYUGRIZZ [ Thu Dec 30, 2010 12:41 pm ] |
| Post subject: | 17x48 X-series W/ 36 PD |
28.5 light load in deep water 26.5 3 guys & hunting gear in less 1' of water |
|
| Author: | curcio13085 [ Thu Dec 30, 2010 1:38 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
excellent review
|
|
| Author: | bullsprig [ Thu Dec 30, 2010 2:48 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
He probably realized that's all that some people on the site care about. |
|
| Author: | BYUGRIZZ [ Thu Dec 30, 2010 2:55 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
| Author: | Seladuckslayer [ Fri Dec 31, 2010 10:31 am ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
do you have a picture? |
|
| Author: | downdabayou [ Fri Dec 31, 2010 2:00 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
ha |
|
| Author: | BYUGRIZZ [ Tue Jan 04, 2011 8:44 am ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
i haven't taken any photos yet but its a camo hull with a gun box, extended deck, drivers box, camo motor with power trim |
|
| Author: | ff154 [ Tue Jan 04, 2011 8:09 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
That's about what mine runs. Same rig minus the camo paint. |
|
| Author: | SP [ Tue Jan 04, 2011 8:56 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
2 mph drop with 3 guys and hunting gear on a non modded motor with a 48" hull..... 
|
|
| Author: | BYUGRIZZ [ Wed Jan 05, 2011 8:03 am ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
i was in deep water when it was only me & shallow when we were coming back from hunting--less than a foot of water |
|
| Author: | BYUGRIZZ [ Wed Jan 05, 2011 10:04 am ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
| Author: | greenhead [ Fri Jan 21, 2011 5:48 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
Is that short or tall transom? and How tall are the sides? |
|
| Author: | Tenpoint [ Fri Jan 21, 2011 7:28 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
| Author: | BYUGRIZZ [ Mon Jan 24, 2011 3:49 pm ] |
| Post subject: | Re: 17x48 X-series W/ 36 PD |
its a tall transom on the low sides we did run in some deeper water with that load & it dropped down to anywhere from 26 all the way to 25 in 5 to 6 feet of water |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|