| MudmotorTalk.com https://www.mudmotortalk.com/mmt_v2/ |
|
| 2014 Gen III Pro Drive on 18x54 mad man custom https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=5&t=51457 |
Page 1 of 1 |
| Author: | teammarshmafia [ Fri Mar 14, 2014 11:11 am ] |
| Post subject: | 2014 Gen III Pro Drive on 18x54 mad man custom |
MM Brand:Pro Drive Horsepower:36 Boat Brand:Mad Man Customs Boat Size: 18x54 Boat Layout: 5 ft front deck, hunt deck in rear, 4" catwalks, 7' rod box on starboard side. Speeds Shallow Water: Speeds Deep Water:26 mph @ 4200 rpms Total Boat Load With Gear Etc:myself (245lbs), my dad (300lbs), my 2 yr old son (35lbs), 6 gal of gas, minn kota 101lb thrust trollin motor, 3 batteries (2 deep cycle and 1 cranking batt.) Conditions Tested In: light current, little to no wind, and deep water Speeds deep water: 27mph @ 4300rpms Total boat load: everything listed above minus my dad and my son. Comments: didnt get to run it in shallow water yet or vary my load any. |
|
| Author: | teammarshmafia [ Fri Mar 14, 2014 11:19 am ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Ill have more information to post as I run it |
|
| Author: | bayouboy [ Fri Mar 14, 2014 11:26 am ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Congrats, Nice Rig for sure. |
|
| Author: | Will [ Fri Mar 14, 2014 11:44 am ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Can you post some pictures of the hull and the layout? Sounds like a good set up. |
|
| Author: | teammarshmafia [ Fri Mar 14, 2014 1:29 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Pics of boat |
|
| Author: | fowllife08 [ Fri Mar 14, 2014 1:44 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Just curious if your gdsd was faster? |
|
| Author: | teammarshmafia [ Fri Mar 14, 2014 2:19 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Running light yes it was, but with a load no it wasn't and im almost always carrying a load. With load described above the go devil would only do about 23mph and with a light load it would run 28 |
|
| Author: | fowllife08 [ Fri Mar 14, 2014 2:22 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Cool, congrats on the motor. |
|
| Author: | pintail_89 [ Fri Mar 14, 2014 7:17 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
good lookin rig man, i got one from him too, wish i would have gotten catwalks as well, they look real good, specially with those lights |
|
| Author: | doubleBanded [ Sat Mar 15, 2014 7:27 am ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Congrats nice rig |
|
| Author: | Buzz Killington [ Sat Mar 15, 2014 8:17 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Very nice |
|
| Author: | WhoDat88 [ Sat Mar 15, 2014 8:31 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Bad ass looking rigs . That's some good speed with a load |
|
| Author: | Frog [ Sun Mar 16, 2014 11:24 am ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Congrats, nice ride |
|
| Author: | teammarshmafia [ Tue Mar 25, 2014 9:49 am ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
Got to run the new pro drive on my lease in delacroix. Got some shallow water speeds and some loaded down speeds. Shallow water with light load was solid 27 mph. We took it bowfishing friday night and had 4 people(250, 290, 200, 160), 150 qt ice chestw/40lbs of ice, bows light bar, 12 gal of gas, and 3 batteries. And boat got on plane and ran 22 mph. In deep water. I was blown away! We shot about 300 lbs of fish friday night and on way back had a little trouble getting it to plane out but eventually it did and did 16mph on the way back in. |
|
| Author: | teammarshmafia [ Tue Mar 25, 2014 6:20 pm ] |
| Post subject: | Re: 2014 Gen III Pro Drive on 18x54 mad man custom |
https://www.youtube.com/watch?v=FKm5ENi ... ata_player |
|
| Page 1 of 1 | All times are UTC - 6 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|