MudmotorTalk.com
https://www.mudmotortalk.com/mmt_v2/

First biuld pics
https://www.mudmotortalk.com/mmt_v2/viewtopic.php?f=6&t=33707		 Page 1 of 1
Author:  Joel907 [ Fri Oct 26, 2012 9:25 am ]
Post subject:  First biuld pics









Any pointers ?
Author:  barnes_53 [ Fri Oct 26, 2012 9:25 am ]
Post subject:  Re: First biuld pics
You're going to need a prop and a case of natty lights.

Good luck and welcome to MMT ;)
Author:  Joel907 [ Sat Oct 27, 2012 7:41 pm ]
Post subject:  Re: First biuld pics
Which prop should I get motor is a One of them honda clones 6.5 hp
I will remove the gov. Put k@n air filter new jet in carb. So it should get 4000 rpms
Author:  Joel907 [ Sun Oct 28, 2012 9:18 pm ]
Post subject:  Re: First biuld pics
Author:  MALLARDSX2 [ Mon Oct 29, 2012 6:46 am ]
Post subject:  Re: First biuld pics
Who the Fuk taught you how to weld??!! Grind those down and lay a nice bead...lol
Author:  Joel907 [ Mon Oct 29, 2012 1:59 pm ]
Post subject:  Re: First biuld pics
No body this was my first time trying to weld. Is it that bad
Author:  Quack Stackin [ Mon Oct 29, 2012 2:11 pm ]
Post subject:  Re: First biuld pics
Almost Looks like you had your gas off
Author:  autogateman [ Mon Oct 29, 2012 2:54 pm ]
Post subject:  Re: First biuld pics
Author:  SwampDonkey1 [ Mon Oct 29, 2012 2:55 pm ]
Post subject:  Re: First biuld pics
Author:  Goday [ Mon Oct 29, 2012 2:56 pm ]
Post subject:  Re: First biuld pics
Yea you might wanna find someone who can weld so shit dont start falling off
Author:  FRANKtheTAU [ Mon Oct 29, 2012 2:58 pm ]
Post subject:  Re: First biuld pics
There was some guy on here like a year ago that couldn't weld and he built his own longtail. The first time he took it out everything but the motor fell off into the lake. Do some practicing and make sure the frame is plenty strong because it will get abused. I also noticed from the pic that you're using one of those little 110v welders. I know they say they'll weld 3/16" but that's really asking a lot from those little welders. Where are you located?
Author:  Joel907 [ Mon Oct 29, 2012 7:32 pm ]
Post subject:  Re: First biuld pics
Flux core yes. I set it on max wire speed 4. I throw it on the shop floor a few times. Really. Hard
I'm in north Texas guess I need to practice a bit before I start the 16 hp biuld.
Ha ha. But for a guy that's never welded I fig go slow make some zig zag motions call it good. I will practice then grind my welds down and do it again. And post pics. How is the base in the second pic is that good
Author:  autogateman [ Mon Oct 29, 2012 9:00 pm ]
Post subject:  Re: First biuld pics
No good. Grind it out and you'll see holes all up in those welds! I weld for a living, trust me it won't hold up.
Author:  SwampDonkey1 [ Mon Oct 29, 2012 9:05 pm ]
Post subject:  Re: First biuld pics
Author:  scottfarm [ Mon Oct 29, 2012 10:18 pm ]
Post subject:  Re: First biuld pics
That motor ain't gonna be able to pull a greased string out of a cat's ass.
Author:  Quack Stackin [ Mon Oct 29, 2012 10:21 pm ]
Post subject:  Re: First biuld pics
Circles, circles that touch both metals with an even bead, no "zig zags". Tach two strips of metal making a "T" and practice on that tell you have an even bead
Author:  CootSlayerRMFT [ Mon Oct 29, 2012 10:45 pm ]
Post subject:  Re: First biuld pics
When you take it out for your first test ride, take video not pics! :lol: :lol:
Author:  Quack Stackin [ Tue Oct 30, 2012 5:54 am ]
Post subject:  Re: First biuld pics
And make sure you have a go pro If you built the boat, because we want to see how badass it is of course
Author:  Joel907 [ Tue Oct 30, 2012 3:52 pm ]
Post subject:  Re: First biuld pics




I have been building. Boats for years.



I make some of the most bad ass layouts around
That one is 45 bls. And Yes I Know My Dog Is Fat and Old but so am I after about 30 years in a duck blind
Who's complaining.
Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/