|
|
FAQ
• Login
|
|
It is currently Sun Jul 06, 2025 2:17 pm
|
|
Page 1 of 1
|
[ 8 posts ] |
|
| Author |
Message |
|
Joel907
MMT Member
Joined: Thu Oct 11, 2012 3:08 pm
Posts: 42
|
 Valve lash Ok up graded to 18bl valve springs set my lash
Now it is hard to pull start. Dang thing will hurt you
Has a bad kick back. Is the lash prob wrong?
|
| Sun Jan 06, 2013 10:12 am |
|
|
|
pokey79
MMT 1000 Club
Joined: Mon Nov 15, 2010 4:50 pm
Posts: 2282
Location: Circumcised, Louisiana
|
Re: Valve lash its possible that u set ur vavles to loose!!!
|
| Sun Jan 06, 2013 11:32 am |
|
|
|
Joel907
MMT Member
Joined: Thu Oct 11, 2012 3:08 pm
Posts: 42
|
Re: Valve lash Factory setting say intake 0.004
And Ext at 0.006
I just reset the at .002 intake and ext at .003
Starts easy now.
Do I take it you can increase torque by play
With your lash? If so which valve lash should I play with.
I also put a alliunium flywheel on the motor
Due to the cast iron one one the motor was Chinese
Do you thank a bunch torque will loss now.
|
| Sun Jan 06, 2013 2:31 pm |
|
|
|
sela_native
MMT Addict
Joined: Sat Sep 10, 2011 11:13 am
Posts: 739
|
Re: Valve lash That may be to tight? Might screw your cam up. Hopefully a more knowledgeable person will clarify
_________________
1650 ribbed abused by a Gt-35 and push pole reverse
|
| Sun Jan 06, 2013 2:42 pm |
|
|
|
take'emgator
MMT Super Elite Member
Joined: Mon Oct 19, 2009 6:38 pm
Posts: 10201
Location: SETX
|
Re: Valve lash Too tight will round off a lobe, factory valve settings are around .005-.006
|
| Sun Jan 06, 2013 4:04 pm |
|
|
|
Joel907
MMT Member
Joined: Thu Oct 11, 2012 3:08 pm
Posts: 42
|
Re: Valve lash So set both valves at .005 when I set them before I couldn't
Start the thing.
|
| Sun Jan 06, 2013 4:34 pm |
|
|
|
Joel907
MMT Member
Joined: Thu Oct 11, 2012 3:08 pm
Posts: 42
|
Re: Valve lash What's a lobe?
|
| Sun Jan 06, 2013 4:35 pm |
|
|
|
sela_native
MMT Addict
Joined: Sat Sep 10, 2011 11:13 am
Posts: 739
|
Re: Valve lash The surfaces on your cam that look all crazy that tells the engine what parts to move and how much. I'm sure there is a better explanation. But I'm sure you get the point
_________________
1650 ribbed abused by a Gt-35 and push pole reverse
|
| Sun Jan 06, 2013 4:43 pm |
|
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 53 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
