| Author |
Message |
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
 Prodrive guys and clutch Have any of you seen this?
Had a problem with the pto constant drive switch and then it just went out one day. The momentary button still worked until today. I just put a bungi cord around it to get by. That went out. I orderd a new switch already should have it tomorrow, but have any of you seen this issue. I have traced and wiggled wires and what not and I do not see any issues with them.
|
| Thu Nov 04, 2010 6:49 pm |
|
|
|
naj
MMT 1000 Club
Joined: Fri Jan 22, 2010 8:40 pm
Posts: 1620
Location: Larose, Louisiana
|
Re: Prodrive guys and clutch If both switches arent working it might be the clutch.
_________________
18' X 48" Center Console Sportsman Fab with a Yamaha F70LA
18' X 48" Center Console Sportsman Fab Dragging a 36hp ProDrive
15' X 42" Sea Arch with a 27hp ProDrive
|
| Thu Nov 04, 2010 7:31 pm |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch The clutch was working before, the constand pull out switch wouldn't work, but the momentary would. I do not think it is the clutch. Anyone have issues with their switch.
|
| Thu Nov 04, 2010 8:07 pm |
|
|
|
Joe M
MMT 1000 Club
Joined: Tue Nov 03, 2009 6:24 pm
Posts: 1025
Location: Tyler, TX
|
Re: Prodrive guys and clutch
_________________
"You may all go to hell, as for me I'm going to Texas" D. Crockett
What is best in life?
To crush your enemies, to see them driven before you, and to hear the lamentations of their women.
|
| Thu Nov 04, 2010 8:38 pm |
|
|
|
naj
MMT 1000 Club
Joined: Fri Jan 22, 2010 8:40 pm
Posts: 1620
Location: Larose, Louisiana
|
Re: Prodrive guys and clutch
_________________
18' X 48" Center Console Sportsman Fab with a Yamaha F70LA
18' X 48" Center Console Sportsman Fab Dragging a 36hp ProDrive
15' X 42" Sea Arch with a 27hp ProDrive
|
| Thu Nov 04, 2010 9:10 pm |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch Joe M,
What was wrong with the wires going into the clutch? My wiring harness wires have wiggled lose, but I have never noticed anything with the clutch I guess. What should I look for.
|
| Fri Nov 05, 2010 7:07 am |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch naj, What did you do to fix this problem that you had?
|
| Fri Nov 05, 2010 7:08 am |
|
|
|
naj
MMT 1000 Club
Joined: Fri Jan 22, 2010 8:40 pm
Posts: 1620
Location: Larose, Louisiana
|
Re: Prodrive guys and clutch
_________________
18' X 48" Center Console Sportsman Fab with a Yamaha F70LA
18' X 48" Center Console Sportsman Fab Dragging a 36hp ProDrive
15' X 42" Sea Arch with a 27hp ProDrive
|
| Fri Nov 05, 2010 7:35 am |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch What should I look for and how should I investigate it? I want to be able to solve this issue very quickly.
|
| Fri Nov 05, 2010 9:42 am |
|
|
|
Joe M
MMT 1000 Club
Joined: Tue Nov 03, 2009 6:24 pm
Posts: 1025
Location: Tyler, TX
|
Re: Prodrive guys and clutch Inspect the wires that go into the clutch very close, right at the point where they go into it. Thats where my problem originated.
_________________
"You may all go to hell, as for me I'm going to Texas" D. Crockett
What is best in life?
To crush your enemies, to see them driven before you, and to hear the lamentations of their women.
|
| Fri Nov 05, 2010 10:06 am |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch After 30 minutes on the phone with brian from prodrive we think we found the issue of needing a new clutch like you guys had said. Somewhere from the two wire plug to where it goes into the clutch there is a short. Has to be because that wire is getting hot as f$ck
|
| Mon Nov 08, 2010 5:54 pm |
|
|
|
naj
MMT 1000 Club
Joined: Fri Jan 22, 2010 8:40 pm
Posts: 1620
Location: Larose, Louisiana
|
Re: Prodrive guys and clutch Clutch is shorted out. I bet when its taken apart its outer plastic protective covering is melted and wires are broken.
_________________
18' X 48" Center Console Sportsman Fab with a Yamaha F70LA
18' X 48" Center Console Sportsman Fab Dragging a 36hp ProDrive
15' X 42" Sea Arch with a 27hp ProDrive
|
| Mon Nov 08, 2010 6:41 pm |
|
|
|
J Wales
MMT Pro Member
Joined: Tue Jan 13, 2009 5:16 pm
Posts: 88
|
Re: Prodrive guys and clutch go ahead and replace the switch too...when the clutch shorted out, it probably fried the switch.
_________________
1848 Brother w/ 36 PD
|
| Tue Nov 09, 2010 9:36 am |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch Thanks, they already told me both were coming out to me.
|
| Tue Nov 09, 2010 11:15 pm |
|
|
|
stumpjumer
MMT Member
Joined: Mon Jun 28, 2010 3:00 pm
Posts: 8
|
Re: Prodrive guys and clutch let me ask you guys a question how many hours did you have on your engine when your clutch went out? i am having to replace mine too on my 2007 prodrive thats got 50 hours on it...
|
| Tue Nov 16, 2010 11:44 am |
|
|
|
cbrown
MMT Pro Member
Joined: Wed Aug 04, 2010 1:45 pm
Posts: 108
Location: Dallas, TX
|
Re: Prodrive guys and clutch I have a 09 36 and the clutch went out around 50hrs. PD covered me for the new clutch and haven't had any problems with it after 30 hrs.
_________________
09 1848 PD X-Series/ 36 PD
|
| Tue Nov 16, 2010 1:48 pm |
|
|
|
naj
MMT 1000 Club
Joined: Fri Jan 22, 2010 8:40 pm
Posts: 1620
Location: Larose, Louisiana
|
Re: Prodrive guys and clutch
_________________
18' X 48" Center Console Sportsman Fab with a Yamaha F70LA
18' X 48" Center Console Sportsman Fab Dragging a 36hp ProDrive
15' X 42" Sea Arch with a 27hp ProDrive
|
| Tue Nov 16, 2010 5:38 pm |
|
|
|
sedlmayrje1723
MMT Pro Member
Joined: Tue May 04, 2010 9:13 pm
Posts: 197
|
Re: Prodrive guys and clutch
|
| Tue Nov 16, 2010 5:56 pm |
|
|
|
DUCKSBANE
MMT Pro Member
Joined: Mon Feb 23, 2009 8:13 pm
Posts: 121
|
Re: Prodrive guys and clutch I got 50 on my first one which was replaced by PD. My second has 250 on it and no trouble.
_________________
1860 Phowler Extreme W/ stage 1 36 PD
|
| Tue Nov 16, 2010 7:56 pm |
|
|
|
coastal
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:29 am
Posts: 1890
Location: South TX
|
Re: Prodrive guys and clutch Had one go out on my 08 PD with 20 something hours.Now have 140 on the new one.
_________________
I will keep my gun's,freedom and money.You can keep your change!
|
| Wed Nov 17, 2010 9:23 am |
|
|
|
