|
|
FAQ
• Login
|
|
It is currently Fri Jun 20, 2025 3:51 pm
|
|
Page 1 of 1
|
[ 9 posts ] |
|
Prodrive problem. Got me Stumped
| Author |
Message |
|
swamprooter
MMT Member
Joined: Mon Jan 19, 2009 9:54 am
Posts: 48
|
 Prodrive problem. Got me Stumped I have a PD 36 that when I put it in gear and under load, it will violently jerk the tiller and cut off. It will crank and run like a bat out hell in neutral or prop in gear out of water. But soon as it has to push boat, motor sta rts shakin and it cuts off. What In world is going on? Help. Thanks
|
| Tue Dec 24, 2013 1:03 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: Prodrive problem. Got me Stumped Sounds like you have a bad bearing or bearings in the lower unit. Can you spin the prop by hand?
|
| Tue Dec 24, 2013 1:15 pm |
|
|
|
JIMMY W
MMT 1000 Club
Joined: Tue Jan 13, 2009 8:02 pm
Posts: 4534
Location: South Louisiana
|
Re: Prodrive problem. Got me Stumped missing on one cylinder!
_________________
17/54 GT EXTREME Center Console, Huntdeck w/ GTR 35
Hoyt Mods and some other goodies
|
| Tue Dec 24, 2013 1:36 pm |
|
|
|
JIMMY W
MMT 1000 Club
Joined: Tue Jan 13, 2009 8:02 pm
Posts: 4534
Location: South Louisiana
|
Re: Prodrive problem. Got me Stumped bad bearing and it would do it out of the water also!
_________________
17/54 GT EXTREME Center Console, Huntdeck w/ GTR 35
Hoyt Mods and some other goodies
|
| Tue Dec 24, 2013 1:37 pm |
|
|
|
swamprooter
MMT Member
Joined: Mon Jan 19, 2009 9:54 am
Posts: 48
|
Re: Prodrive problem. Got me Stumped I can spin prop with my hand. I can put in gear and putt around forward but as soon as I give it some gas it will jerk and go dead
|
| Tue Dec 24, 2013 1:55 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: Prodrive problem. Got me Stumped
|
| Tue Dec 24, 2013 3:57 pm |
|
|
|
swamprooter
MMT Member
Joined: Mon Jan 19, 2009 9:54 am
Posts: 48
|
Re: Prodrive problem. Got me Stumped So I can put it in gear out of water and it will run 4000 rpm with no evidence of a prib. Would that still be a bearing? How hard is it to fix a bearing. I barely know difference between a friut basket and a head gasket but aint scared to learn
|
| Tue Dec 24, 2013 4:21 pm |
|
|
|
bayouboy
MMT Elite Member
Joined: Tue Jan 13, 2009 6:08 pm
Posts: 5376
Location: Venice, La
|
Re: Prodrive problem. Got me Stumped I find the easiest way to check a dead cylinder is to fire it up and check each exhaust port to see which one gets hot. The cold one is dead. Or you can pull the plug wires one at a time.
|
| Tue Dec 24, 2013 6:39 pm |
|
|
|
swamprooter
MMT Member
Joined: Mon Jan 19, 2009 9:54 am
Posts: 48
|
Re: Prodrive problem. Got me Stumped Thankz guys! Found the problem. Embarrassed to say it was a bad plug. Replaced the dirtyplug and cylinder hit right up
|
| Wed Dec 25, 2013 3:37 pm |
|
|
|
|
|
Page 1 of 1
|
[ 9 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 219 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
