|
It is currently Sun May 04, 2025 1:05 am
|
|
Page 1 of 1
|
[ 10 posts ] |
|
Author |
Message |
Ari.P
MMT Member
Joined: Fri Jul 12, 2013 6:39 am Posts: 41 Location: Nederland, TX
|
 18x54 w/35GTR
Well, 6 months, and 74 hours later, I think I can finally write my review. First off, let me say, this is my first MM I've owned, not the only one I've ran.
Hull:2015 Gator Tail 18x54 Extreme Hull Motor:2015 Gator Tail 35 LS w/SS exhaust
Flat bow, with the hunt deck, extended deck, bow rails, spud holes on front left, front right, back left, 2" receiver, nat gear camo, 12v 55lb MK SW trolling motor, 8 ft PP blade, hydro turf throughout.
With the factory 3 blade prop, the fastest I have seen on GPS is 30. That was with the fresh prop, a 2 man beer load at 3750 rpms.
Under a load, I have been extremely pleased. A pic below shows the load I had Wednesday. at 3350 RPMS, I ran 26 in 18" of water. Me (250) Buddy(270) Buddy (180) Gfry(1somethingish) 4 dozen decoys, 2 sleds, blind bags and guns.
So far, the rig is holding up pretty well. She's traveled to Arkansas and hunted the timber, Louisiana and hunted the marshes, along with my home salt/fresh marshes. So far this year we've made in the area of 45 hunts with a month left. I couldn't be more pleased with the versatility of my rig. I fish out of it often, and It's plenty room enough for 3 people on the front deck throwing tails.
Happy to answer any questions. Thanks.
You do not have the required permissions to view the files attached to this post.
|
Fri Dec 26, 2014 4:16 pm |
|
 |
Ari.P
MMT Member
Joined: Fri Jul 12, 2013 6:39 am Posts: 41 Location: Nederland, TX
|
 Re: 18x54 w/35GTR
more..
You do not have the required permissions to view the files attached to this post.
|
Fri Dec 26, 2014 4:19 pm |
|
 |
Ari.P
MMT Member
Joined: Fri Jul 12, 2013 6:39 am Posts: 41 Location: Nederland, TX
|
 Re: 18x54 w/35GTR
more...
You do not have the required permissions to view the files attached to this post.
|
Fri Dec 26, 2014 4:21 pm |
|
 |
txmudcutter
MMT 1000 Club
Joined: Mon Jan 30, 2012 9:08 am Posts: 2307 Location: Nederland, TX (SETX)
|
 Re: 18x54 w/35GTR
Good looking rig man
|
Fri Dec 26, 2014 4:44 pm |
|
 |
Hernaja1
MMT 1000 Club
Joined: Tue Feb 19, 2013 11:29 am Posts: 2465 Location: Sulphur , La
|
 Re: 18x54 w/35GTR
Very nice rig !
_________________ Dual 37 EFI GTR's pushing a 20/72 , CC, point bow , Old school drake Camo Willet custom.
|
Sat Dec 27, 2014 12:47 am |
|
 |
mud slinger 69
MMT 1000 Club
Joined: Sun Aug 28, 2011 4:27 pm Posts: 1194 Location: Utah
|
 Re: 18x54 w/35GTR
Looks good
_________________ We ant just mormons and polyganists we got rednecks too
|
Sat Dec 27, 2014 4:51 am |
|
 |
lastchance
MMT 1000 Club
Joined: Wed Feb 09, 2011 1:56 pm Posts: 1646 Location: Chauvin
|
 Re: 18x54 w/35GTR
Good looking rig!
|
Sat Dec 27, 2014 2:30 pm |
|
 |
calphil
MMT 1000 Club
Joined: Sun Feb 26, 2012 10:49 pm Posts: 1715 Location: Kingwood,TX
|
 Re: 18x54 w/35GTR
Nice ride ...
That pond with teals looks familiar
_________________ 1744 WC Custom 25 GTR
|
Sat Dec 27, 2014 7:29 pm |
|
 |
buffalorider
MMT Member
Joined: Mon Feb 02, 2009 11:14 am Posts: 33
|
 Re: 18x54 w/35GTR
You took that thing in the timber with a power pole on it? How in the hell did you not break it off? Hell, a limb broke the key off in my ignition yesterday.
Sent from my iPhone using Tapatalk
|
Mon Dec 29, 2014 7:51 am |
|
 |
Ari.P
MMT Member
Joined: Fri Jul 12, 2013 6:39 am Posts: 41 Location: Nederland, TX
|
 Re: 18x54 w/35GTR
Very very carefully. The PP has taken a beating, no doubt. I do my best to not ding it while running WOT. Idling is a different story. I've been pleased with the performance so far.
You do not have the required permissions to view the files attached to this post.
|
Tue Dec 30, 2014 10:20 pm |
|
 |
|
|
Page 1 of 1
|
[ 10 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 56 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|