|
|
FAQ
• Login
|
|
It is currently Wed May 14, 2025 5:13 pm
|
|
Page 1 of 1
|
[ 12 posts ] |
|
| Author |
Message |
|
ScottC
MMT Member
Joined: Sun May 01, 2016 8:05 am
Posts: 17
|
 Shaft Collar ?? Anybody know where I can get a shaft collar with key way and set screws that is 3/4" one end and 1" on other end?
|
| Fri May 06, 2016 3:40 pm |
|
|
|
brycecheramie
MMT 1000 Club
Joined: Thu Nov 04, 2010 7:38 am
Posts: 4323
Location: Cut Off, La.
|
Re: Shaft Collar ?? like, a U-Joint?
_________________
Refurbishing a Prodrive
|
| Fri May 06, 2016 5:52 pm |
|
|
|
jc
MMT 1000 Club
Joined: Sun Oct 24, 2010 7:19 pm
Posts: 1103
|
Re: Shaft Collar ?? Grainger but they are high.
|
| Fri May 06, 2016 6:01 pm |
|
|
|
jaycee159
MMT Member
Joined: Sun Mar 20, 2016 8:35 pm
Posts: 20
|
Re: Shaft Collar ?? Shaft collar is usually just 1 size. Is This what you are referring to?
Sent from my iPhone using Tapatalk
|
| Fri May 06, 2016 6:02 pm |
|
|
|
ScottC
MMT Member
Joined: Sun May 01, 2016 8:05 am
Posts: 17
|
Re: Shaft Collar ??
|
| Fri May 06, 2016 8:33 pm |
|
|
|
ScottC
MMT Member
Joined: Sun May 01, 2016 8:05 am
Posts: 17
|
Re: Shaft Collar ??
|
| Fri May 06, 2016 8:37 pm |
|
|
|
jaycee159
MMT Member
Joined: Sun Mar 20, 2016 8:35 pm
Posts: 20
|
Re: Shaft Collar ??
|
| Fri May 06, 2016 8:45 pm |
|
|
|
umahunter
MMT Pro Member
Joined: Thu Sep 24, 2009 4:18 pm
Posts: 83
Location: yuma AZ
|
Re: Shaft Collar ?? What's it for ???
|
| Sat May 07, 2016 2:18 am |
|
|
|
ScottC
MMT Member
Joined: Sun May 01, 2016 8:05 am
Posts: 17
|
Re: Shaft Collar ??
|
| Sat May 07, 2016 9:00 am |
|
|
|
Cajunwannabe
MMT Pro Member
Joined: Wed Jan 28, 2009 3:40 pm
Posts: 188
Location: Wishing I was in SE La.
|
Re: Shaft Collar ?? Buy a 1" x 1" coupling and then put a bushing in on the 3/4" side for your shaft to make it 3/4". I did that one my motor 3 years ago and haven't had a single issue. I took a dremel and cut a notch in it for the key to slide in.
If you think a 1" x 3/4" coupling is high price a 1" x 1 1/8" coupling. It was a whole lot cheaper for me to buy a 1 1/8 x 1 1/8 coupling and do the above with a bushing than paying for an odd size coupling.
I would stay away from the 3 piece couplings with the plastic spider.
My straight shaft is a 25 hp. What size motor are you using?
|
| Sun May 08, 2016 12:54 pm |
|
|
|
fireman1293
MMT Pro Member
Joined: Fri Dec 25, 2009 7:09 pm
Posts: 102
|
Re: Shaft Collar ??
|
| Fri May 13, 2016 11:36 am |
|
|
|
umahunter
MMT Pro Member
Joined: Thu Sep 24, 2009 4:18 pm
Posts: 83
Location: yuma AZ
|
Re: Shaft Collar ?? Do you know anyone with a lathe ?? If not maybe you can take it to a machinist and have half of it bored out to the size you need
|
| Fri May 13, 2016 7:36 pm |
|
|
|
|
|
Page 1 of 1
|
[ 12 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 94 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
