Thanks! Got the hatches and latches in today and will have them in this weekend. All my lime green led's will b n next week!

I noticed you are from Jacksonville, that right? If so and you ever decide you want to change something, want to add somethin (bowfishing deck or whatever), or need something fixed, my shop is in Flint, TX and do custom fabrication and such. Just in case you don't want to drive back up there to that guy.

Again very nice boat!

Cool deal! Thanks

Got my motor and mounted it today. Going to hook it up and run it a little tomorrow. May have to get the longer handle. It is ok until I have to turn right. Is that normal? If I wanted to make a tight turn I will have to stand up.

That's a real unique boat, I like it.

Is it normal to not be able to turn all the way to the right without standing?

Yea that's fine, with as wide of a boat as it is, it'd be almost impossible for anyone to pull that off

Where did you order the LED's from?

Got it in the pond today to test it out. Only have 150+/- yards before I have to shut it down and it ran 25.4 in deep water. Forgot to look and see what the rpms were but I will check later. Sitting still the back was floating about 2.5-3 Inches. Ready to get it on the lake and see what it will really do.

Is that motor gunna hit the huntdeck when it kicks up?

I picked it up as far as it would go and had plenty of room.

I still have a lot of work to do on it. Just had to get it n the water and mess with it. Couldn't resist!

Just ran it again to get rpm. Got 25.9 @ 3650. What are yalls WFO rpms? I think that is pretty low. But I am new to the SD and auto trim so it will take a little time to get it down. I was still climbing speed when I shut it down to not jump the dam.

Lol looks like it's time to invest in a boat trailer

Lmao. I have one but am redoing it so I had the boat laying n the pasture. Just winched it up on that 16ft to get it n the water. Trailer should be done this weekend.

Little help with the RPMs? What does yalls run wide open, trimmed right stock?

My RPMs on the trailer is 4200 - 4250. In water WOT is around 3900.

Yea. I was running half in half out. I just haven't had much time with this motor and don't have enough room to get it maxes out I don't guess

Is it a stock gator tail prop? What is ur out of water RPM's?

Yea. It is stock. Don't know out of water RPM. I still have it in the pond until my trailer is finished.

Ran the boat up about 4 ft out of the water yesterday and got it back n the water by myself. Not near as heavy as I thought! it is at the painter now. I am ready to ride.

Should be done with paint tomorrow!

Paint looks cool man, its different!

Thanks. That's why I got it. I will have burlap on it while hunting. Just wanted a good paint job. Got a great price too!

Got it back today.

how you going to get to the winch?

It is mounted right inside the front hatch. Has wireless remote so I can run it from anywhere.

I am out of town right now but will when I get back. The mount is welded to the uprights on the deck. U could weld it to the bottom runners but then it would take up room.

love the diamond plate. that shop does some slick work! Do you have an idea of what that hull weighs?

nice build man. Tell Ty to come on over and pimp some hulls.


I bet the speed is about all you going to get out of it. Once you weight it down you iwll see a consistant 22-24 nothing wrong with that.


Who did the paint?

Hunter lovelady in winnsboro tx did the paint. If anyone wants his number to get a price or whatever just send me a pm. It's a pretty good price.

I have no idea what the hull weighs. It is light enough for me to pick it up until the motor hits the ground. I'm sure Ty wouldn't mind doing some boats for others.

Where you got those lights? I like em

I just googled 12v led and scrolled through. These are seaworthy brand 4". They aren't as bright as I thought they would be but it does light up the whole boat. I have white ones in each hatch and they are bright enough that I will be able to see everything.

is that 16'plus the hunt deck or 16' overall?

16 + huntdeck. Huntdeck is 24" which I thought was going to be too long but it is perfect once the motor is trimmed up.