| Author |
Message |
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
 my mud motor build Just the start.
You do not have the required permissions to view the files attached to this post.
|
| Tue Feb 14, 2012 6:34 pm |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build Cavitation build
You do not have the required permissions to view the files attached to this post.
|
| Tue Feb 14, 2012 6:56 pm |
|
|
|
Buzz Killington
MMT 1000 Club
Joined: Tue Jan 10, 2012 12:33 pm
Posts: 2455
|
my mud motor build Looks good so far
Keep it up
_________________
Support your troops - they support you
B. MacDonald
|
| Tue Feb 14, 2012 8:05 pm |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build Im not gonna bend the tabs on the cavitation plate to 45 degrees, im gonna leave them bent down just half way down. Any experience with that?
|
| Tue Feb 14, 2012 8:17 pm |
|
|
|
Missouriducks
MMT Member
Joined: Wed Feb 15, 2012 12:07 am
Posts: 27
|
Re: my mud motor build That's about how far mine are bent down. Probably will have to see if it works the best when you get in the water and start running it.
|
| Sat Mar 03, 2012 8:50 am |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build 1st part of the transome build. It is just tack welded for operation.
You do not have the required permissions to view the files attached to this post.
|
| Mon Mar 05, 2012 7:07 am |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build Fresh off the welder. Still lots of slag!!! I will clean it off and it will be pretty. Transom base finished.
You do not have the required permissions to view the files attached to this post.
|
| Mon Apr 09, 2012 8:02 pm |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build more
You do not have the required permissions to view the files attached to this post.
|
| Mon Apr 09, 2012 8:04 pm |
|
|
|
PaleoHuntr
MMT 1000 Club
Joined: Mon Feb 21, 2011 5:21 pm
Posts: 1800
Location: Idaho Falls, ID
|
Re: my mud motor build That is looking pretty good! What engine are you gonna put on it?
_________________
1976 16X48 Lowe powered by a 25hp MB LT and dino turds
To have really lived, you must have almost died. To those who have fought for it, freedom has a flavor the protected will never know.
|
| Mon Apr 09, 2012 8:06 pm |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build duromax 16hp
|
| Mon Apr 09, 2012 8:23 pm |
|
|
|
Rendon_6
MMT Pro Member
Joined: Sat Jun 04, 2011 12:45 pm
Posts: 81
Location: Hooper, Utah
|
my mud motor build I ran a duromax this season with good results
|
| Mon Apr 09, 2012 11:00 pm |
|
|
|
blackduck
MMT Pro Member
Joined: Mon Nov 14, 2011 4:07 pm
Posts: 145
Location: Nevada
|
Re: my mud motor build That is good to know!! I wasn't sure which one to get, but with a limited budget, the duromax should do just fine.
|
| Tue Apr 10, 2012 8:48 am |
|
|
|
