Author |
Message |
swampfox1
MMT Pro Member
Joined: Mon May 07, 2012 7:21 am Posts: 112
|
 brother breaux outboard build
finally got her rigged with 90 hp yamaha. b&b 19ft x 60 with v bow 23 in. sides with 6in catwalks center console
she ran like a scalded dog at 38 knots with 20 gallons fuel. super stable and very happy with handling perforormance.
need some advice though. she was built with mud boat style trim tabs on each transom corner. the more i try to trim her up while underway the more bow is shoved downward. its almost like an opposite effect. any corrective thoughts on this would be appreciated. would cutting tabs off be my cure? having trouble with pic post but can send pic to someone on here via i phone if they will post it.
swampfox
|
Wed May 08, 2013 7:52 am |
|
 |
swampfox1
MMT Pro Member
Joined: Mon May 07, 2012 7:21 am Posts: 112
|
 Re: brother breaux outboard build
well, any any thoughts on trim ?
|
Wed May 08, 2013 7:59 am |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: brother breaux outboard build
ImageUploadedByTapatalk1368022062.470066.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 1754 GTB / 35 GTR
|
Wed May 08, 2013 8:08 am |
|
 |
DD
MMT Pro Member
Joined: Thu Feb 14, 2013 7:28 am Posts: 179 Location: Central FL
|
 Re: brother breaux outboard build
are you talking about trimming the motor up or the tabs?
_________________ 16/42 crawfish skiff - 31GDLT
|
Wed May 08, 2013 8:11 am |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: brother breaux outboard build
That dude builds a fine boat, sonbitch.
not sure how to help with the trim. heres a pic of the rear of my river boat. flat bottom small tabs in back, but i do not have the problem with the boat diving when i trim up
You do not have the required permissions to view the files attached to this post.
_________________ 1754 GTB / 35 GTR
|
Wed May 08, 2013 8:11 am |
|
 |
BayouBuster
MMT 1000 Club
Joined: Sat Jun 25, 2011 8:33 am Posts: 1352 Location: Genoa AR
|
 Re: brother breaux outboard build
Try bending the tabs up.
|
Wed May 08, 2013 8:16 am |
|
 |
doubleBanded
MMT 1000 Club
Joined: Sun Feb 03, 2013 1:26 pm Posts: 3084 Location: Down South
|
 Re: brother breaux outboard build
Boat looks good! X2 on trim tabs
_________________ 1852 Dfou custom 35gtr
|
Wed May 08, 2013 9:37 am |
|
 |
swampfox1
MMT Pro Member
Joined: Mon May 07, 2012 7:21 am Posts: 112
|
 Re: brother breaux outboard build
i think i figured it out . had motor hung too low and cavitation plate was below bottom of transom. unbolted and raised motor to 3rd bolt hole and gonna try out today. anyone ever dealt with this on outboard? swamp....
|
Thu May 09, 2013 6:30 am |
|
 |
swampfox1
MMT Pro Member
Joined: Mon May 07, 2012 7:21 am Posts: 112
|
 Re: brother breaux outboard build
i think i figured it out . had motor hung too low and cavitation plate was below bottom of transom. unbolted and raised motor to 3rd bolt hole and gonna try out today. anyone ever dealt with this on outboard? swamp....
|
Thu May 09, 2013 6:31 am |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: brother breaux outboard build
def dont want the cav plate below the bottom of the boat, if anything hang an inch or two above. should be aite. send me a couple pics to post.
_________________ 1754 GTB / 35 GTR
|
Thu May 09, 2013 10:53 am |
|
 |
swampfox1
MMT Pro Member
Joined: Mon May 07, 2012 7:21 am Posts: 112
|
 Re: brother breaux outboard build
10-4
|
Thu May 09, 2013 10:58 am |
|
 |
duckhunter888
MMT F.E.
Joined: Wed Jan 14, 2009 10:44 pm Posts: 828 Location: North Texas
|
 Re: brother breaux outboard build
Hey Swampfox, please post a few more pics of your boat, especially the front end, is that a mod v into a flat?,looks good
_________________ Crisis defines character
|
Fri May 10, 2013 5:21 am |
|
 |
cajundan
MMT Pro Member
Joined: Mon Feb 02, 2009 9:59 am Posts: 160 Location: Marshville, Texas
|
 Re: brother breaux outboard build
Jackplate. It gives you setback and rise.
Sent from my C771 using Tapatalk 2
_________________ From the front line to a huntin blind... Banded Brigade Outdoors www.bandedbrigadeoutdoors.org
|
Fri May 10, 2013 6:36 am |
|
 |
swampfox1
MMT Pro Member
Joined: Mon May 07, 2012 7:21 am Posts: 112
|
 Re: brother breaux outboard build
boat is at crab dock and will be there this afternoon to take some more pics. yes it is modv into flat. have contemplated jack plate but am broke after hydro-steering and motor purchase last week. gonna try out adjusted cav-plate today. krogers, i am gonna send u some pics via phone.
swamp......
|
Fri May 10, 2013 8:46 am |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: brother breaux outboard build
ImageUploadedByTapatalk1368199983.636597.jpg
ImageUploadedByTapatalk1368200000.044612.jpg
ImageUploadedByTapatalk1368200010.787130.jpg
You do not have the required permissions to view the files attached to this post.
_________________ 1754 GTB / 35 GTR
|
Fri May 10, 2013 9:34 am |
|
 |
krogers
MMT 1000 Club
Joined: Fri Oct 29, 2010 8:24 am Posts: 1958 Location: Bristol, FL
|
 Re: brother breaux outboard build
ImageUploadedByTapatalk1368200058.461362.jpg
ImageUploadedByTapatalk1368200068.615123.jpg
Good talkin with you, swampfox. Badass boat too.
You do not have the required permissions to view the files attached to this post.
_________________ 1754 GTB / 35 GTR
|
Fri May 10, 2013 9:35 am |
|
 |
|