It is currently Wed May 14, 2025 5:03 am




Reply to topic  [ 7 posts ] 
 RPM and Speed question 
Author Message
MMT Member
User avatar

Joined: Sun Jan 18, 2009 5:32 pm
Posts: 21
Post RPM and Speed question
I have a light modded 23lt and I am turning 3850 in water with a 9x7 running 22mph and turning a 9x6 4000 running 22mph....any ideas???? Am I topped out or can I get more?


Wed Aug 03, 2011 1:31 pm
Profile
MMT 1000 Club
User avatar

Joined: Wed Jan 14, 2009 8:58 pm
Posts: 2731
Location: Lafayette, LA
Post RPM and Speed question
With those props I doubt you will get anything higher. You are probably running about 20-21 at 3600 and then that. I think you are at the top of the curve right now.

_________________
1644 WeldCraft / 27 GDLT
Ranger R71 / 125 Merc


Wed Aug 03, 2011 3:10 pm
Profile
MMT Member
User avatar

Joined: Sun Jan 18, 2009 5:32 pm
Posts: 21
Post Re: RPM and Speed question
So would getting someone such as Hopkins to tune up a prop to say 9x8 or 9x9 help any?


Wed Aug 03, 2011 8:00 pm
Profile
MMT 1000 Club
User avatar

Joined: Wed Jan 14, 2009 8:58 pm
Posts: 2731
Location: Lafayette, LA
Post RPM and Speed question
Might wanna wait and see if someone with a similar motor chimes in.

_________________
1644 WeldCraft / 27 GDLT
Ranger R71 / 125 Merc


Wed Aug 03, 2011 8:03 pm
Profile
MMT Member
User avatar

Joined: Sun Jan 18, 2009 5:32 pm
Posts: 21
Post Re: RPM and Speed question
Ok man, appreciate it. I did go run it again today and added some octane boost and got 3950 and bumped 23 a couple times with 2 of us in the boat...only reason I tried that was I was having a detonation/preignition problem and was trying the octane boost for that problem.


Wed Aug 03, 2011 8:14 pm
Profile
MMT Elite Member

Joined: Wed Mar 03, 2010 7:00 pm
Posts: 6060
Location: Choudrant, La
Post Re: RPM and Speed question
What size boat is it on?

Without doing more mods it sounds like you are about peaked out.
What have you done to it?

_________________
CSM Custom 18x42 Battleship with a 36 PD beating you to the hole
My Rig (Old Motor) viewtopic.php?f=5&t=45193

(New Motor) viewtopic.php?f=5&t=54733

Stumps Fear Me


Wed Aug 03, 2011 8:23 pm
Profile
MMT Member
User avatar

Joined: Sun Jan 18, 2009 5:32 pm
Posts: 21
Post Re: RPM and Speed question
Woodie, it is on a 1652 riveted flat with frog spit on bottom. decked heads 15, bored 30 over, polished and 3 angle valve grind, 35 carb, twin exhaust, high flow s&b air filter.


Wed Aug 03, 2011 8:31 pm
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 7 posts ] 

Who is online

Users browsing this forum: No registered users and 115 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: