It is currently Sun Jul 13, 2025 6:39 am




Reply to topic  [ 15 posts ] 
 Speeds 
Author Message
MMT Member

Joined: Sat May 29, 2010 10:15 pm
Posts: 23
Location: Waukee, IA
Post Speeds
What speeds are you guys getting? I just finished putting my longtail together and am looking for some comparisons so I know if things are running right. I have a beavertail longtail frame with a 33 hp generac engine on a 1652 Lowe Roughneck with pods.

I am getting 10-12 with three guys, two dogs, and all of our gear.
18 mph with just me, two kids, and two dogs


Mon Sep 27, 2010 5:47 am
Profile
MMT Super Elite Member

Joined: Fri Dec 18, 2009 8:10 pm
Posts: 16915
Location: Rowlett, TX
Post Re: Speeds
What are your rpm's? Without a load on the trailer? With a light load? With a heavy load? If you don't have a tach, get one!


Mon Sep 27, 2010 9:34 am
Profile
MMT 1000 Club
User avatar

Joined: Wed Sep 02, 2009 2:54 pm
Posts: 1554
Location: SW Georgia
Post Re: Speeds
what size prop are you running?

Should have a little more speed unloaded and alot more speed than you have loaded.

Might be over-propped.

_________________
19x54 Seminole Extreme with a 35hp CDI GDSD. Mikuni. Marsh Mellow. Heads. Cam.


Mon Sep 27, 2010 10:24 am
Profile
MMT Pro Member
User avatar

Joined: Mon Mar 23, 2009 9:07 pm
Posts: 300
Post Re: Speeds
Did you completely build yourself? Where did you get your Generac?


Mon Sep 27, 2010 3:51 pm
Profile
MMT Pro Member
User avatar

Joined: Thu Jan 15, 2009 1:24 am
Posts: 455
Post Re: Speeds


Tue Sep 28, 2010 12:53 am
Profile
MMT Member

Joined: Sat May 29, 2010 10:15 pm
Posts: 23
Location: Waukee, IA
Post Re: Speeds
i bought the frame and prop used as a unit and added the generac motor that i purchased from http://stores.ebay.com/Small-Air-Cooled-Engines. I have a few feelers out there for prop recommendations. I know it is a nine inch prop but i am not sure of the pitch. the original engine was a vanguard 35 that the guy took off and put on a short shaft.


Wed Sep 29, 2010 7:44 pm
Profile
MMT Member

Joined: Sat May 29, 2010 10:15 pm
Posts: 23
Location: Waukee, IA
Post Re: Speeds
If i remember right

rpm on the trailer is around 4000 rpm
around 3800 with the heaier load
around 3900 with the lighter load

the prop is slightly worn which is why i am looking for suggestions on size and brand of new prop


Wed Sep 29, 2010 7:48 pm
Profile
MMT Member

Joined: Sun Sep 12, 2010 6:33 pm
Posts: 45
Post Re: Speeds
I have noticed that most 31 to 35hp motors come with a 9X6. I think I might be slightly overpropped to. I carry a pretty heavy load with a full aluminum blind, 3 dozen weighted keel decoys, 2 robo ducks, 2 200+lb guys, 1 dog, battery. Running a 31hp beavertail I got 14mph average. Haven't tried it bymyself. But either I'm overpowered or the motor isn't at full power because I can tell that it seems to be bogged slightly. You should be able to hear if the motor is bogging down badly, and thats a pretty good clue you need to try a smaller prop.


Thu Sep 30, 2010 9:39 pm
Profile
MMT 1000 Club
User avatar

Joined: Wed Dec 09, 2009 10:35 pm
Posts: 1072
Post Re: Speeds

_________________
14 by 44 Weld Craft powered by a 20hp. go devil longtail
Team Arc Angel Bowfishing


Thu Sep 30, 2010 10:21 pm
Profile
MMT Member

Joined: Sun Sep 12, 2010 6:33 pm
Posts: 45
Post Re: Speeds


Sun Nov 07, 2010 8:00 pm
Profile
MMT 1000 Club
User avatar

Joined: Wed Jan 14, 2009 8:58 pm
Posts: 2731
Location: Lafayette, LA
Post Re: Speeds

_________________
1644 WeldCraft / 27 GDLT
Ranger R71 / 125 Merc


Sun Nov 07, 2010 8:09 pm
Profile
MMT Member

Joined: Sun Nov 22, 2009 3:56 pm
Posts: 14
Location: Hooper UT
Post Re: Speeds
my mblt 35CDI runs a 9X8 on a 16X48 G3MV with 16"podds runs 20 to 22 with me (335) 18 with 2 more guys at 4205 ele

_________________
16X48 G3 MBLT BD4500


Mon Nov 08, 2010 5:12 pm
Profile
MMT 1000 Club
User avatar

Joined: Thu Mar 26, 2009 2:08 pm
Posts: 1229
Location: morgan city, louisiana
Post Re: Speeds
31Hp GDLT on a 17x42 Skiff, 3 ppl.. Me (150), Podnuh1 (195), Podnuh2, (150)
And gear @ at 21 Mph! :)

2 ppl, Full and gear @ 23mph in Deep water an 25mph in shallow.

_________________
36hp Pro-Drive with EVT exhaust pushin a 17x42 custom skiff


Mon Nov 08, 2010 9:31 pm
Profile WWW
MMT 1000 Club
User avatar

Joined: Wed Jan 14, 2009 8:58 pm
Posts: 2731
Location: Lafayette, LA
Post Re: Speeds

_________________
1644 WeldCraft / 27 GDLT
Ranger R71 / 125 Merc


Mon Nov 08, 2010 9:50 pm
Profile
MMT Member

Joined: Sun Nov 07, 2010 6:11 pm
Posts: 25
Location: Crosby,Tx
Post Re: Speeds
18x44 w/ 35 GDLT, 2 people 85lb dog and gear I get 21 or 22 mph at 3800rpm 10x6 prop


Mon Nov 08, 2010 10:27 pm
Profile WWW
Display posts from previous:  Sort by  
Reply to topic   [ 15 posts ] 

Who is online

Users browsing this forum: No registered users and 49 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to: