Author |
Message |
deanlange
MMT Member
Joined: Sat May 29, 2010 10:15 pm Posts: 23 Location: Waukee, IA
|
 Speeds
What speeds are you guys getting? I just finished putting my longtail together and am looking for some comparisons so I know if things are running right. I have a beavertail longtail frame with a 33 hp generac engine on a 1652 Lowe Roughneck with pods.
I am getting 10-12 with three guys, two dogs, and all of our gear. 18 mph with just me, two kids, and two dogs
|
Mon Sep 27, 2010 5:47 am |
|
 |
cb5331
MMT Super Elite Member
Joined: Fri Dec 18, 2009 8:10 pm Posts: 16915 Location: Rowlett, TX
|
 Re: Speeds
What are your rpm's? Without a load on the trailer? With a light load? With a heavy load? If you don't have a tach, get one!
|
Mon Sep 27, 2010 9:34 am |
|
 |
bbb
MMT 1000 Club
Joined: Wed Sep 02, 2009 2:54 pm Posts: 1554 Location: SW Georgia
|
 Re: Speeds
what size prop are you running?
Should have a little more speed unloaded and alot more speed than you have loaded.
Might be over-propped.
_________________ 19x54 Seminole Extreme with a 35hp CDI GDSD. Mikuni. Marsh Mellow. Heads. Cam.
|
Mon Sep 27, 2010 10:24 am |
|
 |
lil_catdaddy
MMT Pro Member
Joined: Mon Mar 23, 2009 9:07 pm Posts: 300
|
 Re: Speeds
Did you completely build yourself? Where did you get your Generac?
|
Mon Sep 27, 2010 3:51 pm |
|
 |
GeeLeDouche
MMT Pro Member
Joined: Thu Jan 15, 2009 1:24 am Posts: 455
|
 Re: Speeds
|
Tue Sep 28, 2010 12:53 am |
|
 |
deanlange
MMT Member
Joined: Sat May 29, 2010 10:15 pm Posts: 23 Location: Waukee, IA
|
 Re: Speeds
i bought the frame and prop used as a unit and added the generac motor that i purchased from http://stores.ebay.com/Small-Air-Cooled-Engines. I have a few feelers out there for prop recommendations. I know it is a nine inch prop but i am not sure of the pitch. the original engine was a vanguard 35 that the guy took off and put on a short shaft.
|
Wed Sep 29, 2010 7:44 pm |
|
 |
deanlange
MMT Member
Joined: Sat May 29, 2010 10:15 pm Posts: 23 Location: Waukee, IA
|
 Re: Speeds
If i remember right
rpm on the trailer is around 4000 rpm around 3800 with the heaier load around 3900 with the lighter load
the prop is slightly worn which is why i am looking for suggestions on size and brand of new prop
|
Wed Sep 29, 2010 7:48 pm |
|
 |
iowaducker06
MMT Member
Joined: Sun Sep 12, 2010 6:33 pm Posts: 45
|
 Re: Speeds
I have noticed that most 31 to 35hp motors come with a 9X6. I think I might be slightly overpropped to. I carry a pretty heavy load with a full aluminum blind, 3 dozen weighted keel decoys, 2 robo ducks, 2 200+lb guys, 1 dog, battery. Running a 31hp beavertail I got 14mph average. Haven't tried it bymyself. But either I'm overpowered or the motor isn't at full power because I can tell that it seems to be bogged slightly. You should be able to hear if the motor is bogging down badly, and thats a pretty good clue you need to try a smaller prop.
|
Thu Sep 30, 2010 9:39 pm |
|
 |
mississippiduckboy
MMT 1000 Club
Joined: Wed Dec 09, 2009 10:35 pm Posts: 1072
|
 Re: Speeds
_________________ 14 by 44 Weld Craft powered by a 20hp. go devil longtail Team Arc Angel Bowfishing
|
Thu Sep 30, 2010 10:21 pm |
|
 |
iowaducker06
MMT Member
Joined: Sun Sep 12, 2010 6:33 pm Posts: 45
|
 Re: Speeds
|
Sun Nov 07, 2010 8:00 pm |
|
 |
kibb
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:58 pm Posts: 2731 Location: Lafayette, LA
|
 Re: Speeds
_________________ 1644 WeldCraft / 27 GDLT Ranger R71 / 125 Merc
|
Sun Nov 07, 2010 8:09 pm |
|
 |
sloaner
MMT Member
Joined: Sun Nov 22, 2009 3:56 pm Posts: 14 Location: Hooper UT
|
 Re: Speeds
my mblt 35CDI runs a 9X8 on a 16X48 G3MV with 16"podds runs 20 to 22 with me (335) 18 with 2 more guys at 4205 ele
_________________ 16X48 G3 MBLT BD4500
|
Mon Nov 08, 2010 5:12 pm |
|
 |
b_coonass
MMT 1000 Club
Joined: Thu Mar 26, 2009 2:08 pm Posts: 1229 Location: morgan city, louisiana
|
 Re: Speeds
31Hp GDLT on a 17x42 Skiff, 3 ppl.. Me (150), Podnuh1 (195), Podnuh2, (150) And gear @ at 21 Mph!  2 ppl, Full and gear @ 23mph in Deep water an 25mph in shallow.
_________________ 36hp Pro-Drive with EVT exhaust pushin a 17x42 custom skiff
|
Mon Nov 08, 2010 9:31 pm |
|
 |
kibb
MMT 1000 Club
Joined: Wed Jan 14, 2009 8:58 pm Posts: 2731 Location: Lafayette, LA
|
 Re: Speeds
_________________ 1644 WeldCraft / 27 GDLT Ranger R71 / 125 Merc
|
Mon Nov 08, 2010 9:50 pm |
|
 |
RB1
MMT Member
Joined: Sun Nov 07, 2010 6:11 pm Posts: 25 Location: Crosby,Tx
|
 Re: Speeds
18x44 w/ 35 GDLT, 2 people 85lb dog and gear I get 21 or 22 mph at 3800rpm 10x6 prop
|
Mon Nov 08, 2010 10:27 pm |
|
 |
|